manualshive.com logo in svg

Comnet CWGE26FX2TX24MSPOE, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE26FX2TX24MSPOE Скачать руководство пользователя страница 83

 INS_CWGE26FX2TX24MSPOE_REV–     5 Mar 2014     PAGE 83

INSTALLATION AND OPERATION MANUAL 

CWGE26FX2TX24MSPOE

TECH SUPPORT: 1.888.678.9427

ACL Control List

Configure an ACE (Access Control Entry) on this page.

An ACE consists of several parameters. These parameters vary according to the frame type that 
you select. First select the ingress port for the ACE, and then select the frame type. Different 
parameter options are displayed depending on the frame type that you selected.

A frame that hits this ACE matches the configuration that is defined here.

Label

Description

Ingress Port

Select the ingress port for which this ACE applies. 
Any: The ACE applies to any port. 
Port n: The ACE applies to this port number, where n is the number of the switch port. 
Policy n: The ACE applies to this policy number, where n can range from 1 through 8.

Frame Type

Select the frame type for this ACE. These frame types are mutually exclusive. 
Any: Any frame can match this ACE. 
Ethernet Type: Only Ethernet Type frames can match this ACE. The IEEE 802.3 specifies 
the value of Length/Type Field specifications should be greater than or equal to 1536 
decimal (equal to 0600 hexadecimal). 
ARP: Only ARP frames can match this ACE. Notice the ARP frames won’t match the ACE 
with Ethernet type. 
IPv4: Only IPv4 frames can match this ACE. Notice the IPv4 frames won’t match the ACE 
with Ethernet type.

Action

Specify the action to take with a frame that hits this ACE. 
Permit: The frame that hits this ACE is granted permission for the ACE operation. 
Deny: The frame that hits this ACE is dropped.

Rate Limiter

Specify the rate limiter in number of base units. The allowed range is 1 to 15. Disabled 
indicates that the rate limiter operation is disabled.

Port Copy

Frames that hit the ACE are copied to the port number specified here. The allowed 
range is the same as the switch port number range. Disabled indicates that the port 
copy operation is disabled.

Содержание CWGE26FX2TX24MSPOE











































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды