Comnet CNGE2FE16MS Скачать руководство пользователя | Manualshive

Страница: 67 / 128

background image

inS_cnge2fe16MS_reV–

01/11/12 Page 67

INSTALLATION AND OPERATION MANUAL

CNGE2FE16MS

TECh SUPPORT: 1.888.678.9427

Port Mirroring

Port Mirroring is a method for monitoring of network traffic on switched networks. Traffic through
ports can be monitored by one specific port, which means traffic going in or out the monitored
(source) ports will be duplicated into the mirroring (destination) port.

Figure 65 – Port Mirroring interface

»

Destination Port

: Select one port to be the destination (mirroring) port for monitoring both

RX and TX traffic coming from the source port. Or, select two ports for monitoring RX traffic
and TX traffic respectively. Users can forward the traffic captured by the mirroring port to the
packet analyzer such as Netxray for further analyses.

»

Source Port

: Select the checkbox to monitor the corresponding port. All monitored port traffic

will be copied to the mirroring (destination) port. Users can select multiple source ports by
selecting the

RX

or

TX

checkboxes.

»

When finished, select the

Apply

button.

«
...
65
66
67
68
69
...
»

Содержание CNGE2FE16MS

































































































































Отзывы:

Нет отзывов

Похожие инструкции для CNGE2FE16MS

Бренд: Talkswitch Страницы: 17

MSD-804FD Series

Бренд: IDK Страницы: 133

Бренд: IDK Страницы: 150

Бренд: IDK Страницы: 101

Бренд: IDK Страницы: 85

Бренд: IDK Страницы: 40

Бренд: IDK Страницы: 97

Бренд: IDK Страницы: 117

Бренд: IDK Страницы: 77

Бренд: LEGRAND Страницы: 2

MyPower S2300-28TC-AC

Бренд: Maipu Страницы: 31

Champion KD-2X1

Бренд: Key Digital Страницы: 12

Бренд: LEGRAND Страницы: 12

Бренд: Optical Systems Design Страницы: 20

Бренд: WIKA Страницы: 8

Бренд: ASTEK Страницы: 3

Бренд: CYP Страницы: 20

Бренд: Ruby Tech Страницы: 254

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды