Comnet CNGE2FE16MS Скачать руководство пользователя страница 82

Страница: 82 / 128

inS_cnge2fe16MS_reV–

01/11/12 Page 82

INSTALLATION AND OPERATION MANUAL

CNGE2FE16MS

TECh SUPPORT: 1.888.678.9427

SNMPV3 Configuration

This tab allows users to configure the SNMPv3 settings for communications via SNMPv3.

Context Table

Configure the SNMPv3 context table. Assign the context name in the field. Select

Apply

to add

the context name added or changed.

User Table

Configure the SNMPv3 user table.

User ID

: Type the user name in the field.

Authentication Password:

Assign the authentication password to the user ID.

Privacy Password

: Assign the private password to the user ID.

Select the

Add

button to create a new user profile.

To remove a user profile, select an entry in the Current User Profiles list box and select the

Remove

button to remove the unwanted user profile.

Group Table

Configure the SNMPv3 group table.

Security Name (User ID)

: Specify the user name that you have set up in the user table.

Group Name

: Type the group name in the field.

Select the

Add

button to create a new group name

To remove a group name, select an entry in the Current Group Content list box and select the

Remove

button to remove the unwanted group.

Содержание CNGE2FE16MS

































































































































Результаты поиска

Содержание CNGE2FE16MS

Отзывы:

Похожие инструкции для CNGE2FE16MS

Бренды по названию

Популярные бренды

Comnet CNGE2FE16MS, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CNGE2FE16MS

Отзывы:

Похожие инструкции для CNGE2FE16MS

Бренды по названию

Популярные бренды