background image

507716-01

Page 47 of 58

Issue 1717

High Altitude Information

NOTE: 

In Canada, certification for installations at elevations over 4500 feet (1371 m) is the jurisdiction of local authorities.

Units may be installed at altitudes up to 10,000 ft. above sea level. See Table 11 for de-rate manifold values. Units installed 

at altitude of 7501 - 10,000 feet require an orifice change. Units installed at altitudes of 4,501 - 10,000 feet (1371 -3048 m) 

may require a pressure switch change which can be ordered separately.

Table 12 lists required pressure switch changes and orifice conversion kits at varying altitudes.

The combustion air pressure switches are factory set and require no adjustment.

Table 12. 

Burner Orifice Conversion Kits at Varying Altitudes

Capacity

0-7,500 ft 

(0-2,286m)

7,501 - 10,000 ft 

(2,286 - 3,048 m)

Natural to LP/

Propane

LP/Propane to 

Natural

High Altitude 

Natural Burner 

Orifice Kit

High Altitude LP/

Propane Burner 

Orifice Kit

045

11K50+

73W80*

51W01

11K45+

070

090

110

135

* Conversion requires installation of a gas valve regulator spring which is provided with the gas conversion 

kit.
+ LP Kits include low line pressure switch.

GUH95C Pressure Switch Requirements at Varying Altitudes

Capacity

0 - 4500 ft 

(0 - 1,371m)

4501 - 7500 ft 

(1371 - 2286m)

7501 - 10000 ft 

(2286 - 3048m)

045

No Change

No Change

11J09

070

No Change

11J12

10U93

090

No Change

11J11

10U93

110

No Change

11J12

10U93

135

No Change

11J11

10U93

Pressure switch is factory set. No adjustment necessary. All models use the factory-installed pressure switch 

from 0-4500 feet (0-1371 m).

Содержание GUH95C



























































Отзывы: