COMFORT-AIRE GUH95C Скачать руководство пользователя

Страница: 28 / 58

507716-01

Page 28 of 58

Issue 1717

VENT TERMINATION CLEARANCES

FOR DIRECT VENT INSTALLATIONS IN THE USA AND CANADA

INSIDE CORNER

DETAIL

VENT TERMINAL

AIR SUPPLY INLET

AREA WHERE TERMINAL

IS NOT PERMITTED

Fixed

Closed

Operable

Fixed

Closed

Operable

A =

B =

C =

D =

E =
F =
G =
H =

I =

J =

K =

L =

M =

US Installations

Canadian Installations

12 inches (305mm) or 12 in. (305mm)

above average snow accumulation.

12 inches (305mm) or 12 in. (305mm)

above average snow accumulation.

Clearance above grade, veranda,

porch, deck or balcony

Clearance to window or

door that may be opened

6 inches (152mm) for appliances <10,000

pliances > 10,000 Btuh (3kw) and <50,000

pliances > 50,000 Btuh (15kw)

6 inches (152mm) for appliances <10,000

Btuh (3kw), 12 inches (305mm) for

appliances > 10,000 Btuh (3kw) and

<100,000 Btuh (30kw), 36 inches (.9m)

for appliances > 100,000 Btuh (30kw)

Clearance to permanently

closed window

Vertical clearance to ventilated soffit

located above the terminal within a

horizontal distance of 2 feet (610mm)

from the center line of the terminal

Clearance to unventilated soffit

Clearance to outside corner

Clearance to inside corner

tended above meter / regulator assembly

Clearance to service regulator

vent outlet

Clearance to non-mechanical air

pliance

ply inlet

Clearance above paved sidewalk or

paved driveway located on public property

Clearance under veranda, porch, deck or balcony

* 12”

* 7 feet (2.1m)

3 feet (.9m) within a height 15 feet (4.5m)

above the meter / regulator assembly

3 feet (.9m)

6 inches (152mm) for appliances <10,000

pliances > 10,000 Btuh (3kw) and <50,000

pliances > 50,000 Btuh (15kw)

6 inches (152mm) for appliances <10,000

Btuh (3kw), 12 inches (305mm) for

appliances > 10,000 Btuh (3kw) and

<100,000 Btuh (30kw), 36 inches (.9m)

for appliances > 100,000 Btuh (30kw)

3 feet (.9m) above if within 10 feet

(3m) horizontally

6 feet (1.8m)

7 feet (2.1m)†

12 inches (305mm)‡

In accordance with the current ANSI Z223.1/NFPA 54 Natural Fuel Gas Code

In accordance with the current CSA B149.1, Natural Gas and Propane Installation Code

*For clearances not specified in ANSI Z223.1/NFPA 54 or CSA

B149.1, clearance will be in accordance with local installation

codes and the requirements of the gas supplier and these

installation instructions.”

† A vent shall not terminate directly above a sidewalk or paved driveway that is located

between two single family dwellings and serves both dwellings.

‡ Permitted only if veranda, porch, deck or balcony is fully open on a minimum of

two sides beneath the floor. Comfort-Aire / Century recommends avoiding this location

if possible.

* 12”

* Equal to or greater than soffit depth

* No minimum to outside corner

3 feet (.9m) within a height 15 feet (4.5m)

above the meter / regulator assembly

3 feet (.9m)

*12 inches (305mm)‡

Btuh (3kw), 9 inches (228mm) for ap-

Btuh (15kw), 12 inches (305mm) for ap-

Clearance to each side of center line ex-

Btuh (3kw), 9 inches (228mm) for ap-

Btuh (15kw), 12 inches (305mm) for ap-

supply inlet to building or the com-

bustion air inlet to any other ap-

Clearance to mechanical air sup-

Figure 35. Vent Termination Clearances for Direct Installations

Содержание GUH95C



























































Результаты поиска

Содержание GUH95C

Отзывы:

Похожие инструкции для GUH95C

Бренды по названию

Популярные бренды

COMFORT-AIRE GUH95C, Руководство по установке

Результаты поиска

Содержание GUH95C

Отзывы:

Похожие инструкции для GUH95C

Бренды по названию

Популярные бренды