COMFORT-AIRE GUH95C Скачать руководство пользователя

Страница: 12 / 58

507716-01

Page 12 of 58

Issue 1717

Figure 16. Removing the Bottom Panel

Removing the Bottom Panel

Remove the two screws that secure the bottom cap to the

furnace. Pivot the bottom cap down to release the bottom

panel. Once the bottom panel has been removed, reinstall

the bottom cap. See Figure 16.

Horizontal Applications

Do not install the furnace on its front or its back. See

Figure 17.

WARNING

Figure 17.

This furnace can be installed in horizontal applications with

either right or left hand air discharge.

Refer to Figure 18 for clearances in horizontal applications.

Figure 18. Installation Clearances

Horizontal Applications

Right−Hand Discharge

Left−Hand Discharge

Top

Bottom (Floor)**

Air

Flow

Air

Flow

Air

Flow

Air

Flow

Top

Front*

Back

Ends

Vent

Floor

‡

* Front clearance in alcove installation must be 24 in. (610 mm).

Maintain a minimum of 24 in. (610 mm) for front service access.

**An 8" service clearance must be maintained below the unit to provide

for servicing of the condensate trap.

‡

For installations on a combustible floor, do not install the furnace directly

on carpeting, tile or other combustible materials other than wood

flooring.

Top/Plenum

1 in. (25 mm)

* Front

Back

Sides

0†

Vent

Floor

0‡

* Front clearance in alcove installation must be 24 in. (610

mm). Maintain a minimum of 24 in. (610 mm) for front service

access.
† Allow proper clearances to accommodate condensate trap.
‡ For installations on a combustible floor, do not install

the furnace directly on carpeting, tile or other combustible

materials other than wood flooring.

Suspended Installation of Horizontal Unit

This furnace may be installed in either an attic or a crawl

space. Either suspend the furnace from roof rafters or floor

joists, as shown in Figure 19, or install the furnace on a

platform, as shown in Figure 20. A horizontal suspension

kit (51W10) may be ordered from your distributor or use

equivalent.

Figure 19. Typical Horizontal Application

Содержание GUH95C



























































Результаты поиска

Содержание GUH95C

Отзывы:

Похожие инструкции для GUH95C

Бренды по названию

Популярные бренды

COMFORT-AIRE GUH95C, Руководство по установке

Результаты поиска

Содержание GUH95C

Отзывы:

Похожие инструкции для GUH95C

Бренды по названию

Популярные бренды