COMFORT-AIRE GUH95C Скачать руководство пользователя

Страница: 44 / 58

507716-01

Page 44 of 58

Issue 1717

Unit Start-Up

FOR YOUR SAFETY READ BEFORE OPERATING

Do not use this furnace if any part has been underwater.

A flood-damaged furnace is extremely dangerous.

Attempts to use the furnace can result in fire or explosion.

Immediately call a qualified service technician to inspect

the furnace and to replace all gas controls, control

system parts, and electrical parts that have been wet or

to replace the furnace, if deemed necessary.

WARNING

Danger of explosion. Can cause injury or

product or property damage. Should the gas

supply fail to shut off or if overheating

occurs, shut off the gas valve to the furnace

before shutting off the electrical blower

deck, before performing any service

procedure.

WARNING

Before attempting to perform any service or

maintenance, turn the electrical power to unit OFF at

disconnect switch.

CAUTION

BEFORE LIGHTING

the unit, smell all around the furnace

area for gas. Be sure to smell next to the floor because

some gas is heavier than air and will settle on the floor.

The gas valve on the unit is equipped with a gas control

switch (lever). Use only your hand to move switch. Never

use tools. If the switch will not move by hand, do not try to

repair it. Force or attempted repair may result in a fire or

explosion.

Placing the Furnace into Operation

This furnace is equipped with an automatic hot surface

ignition system. Do not attempt to manually light burners

on this furnace. Each time the thermostat calls for heat, the

burners will automatically light. The ignitor does not get hot

when there is no call for heat on these units.

Figure 68. Integrated Control

(Automatic Hot Surface Ignition System)

Terminal Designations

120 HUM

Humidifier (120 VAC)

LINE

Input (120 VAC)

XFMR

Transformer (120 VAC)

CIRC

Indoor Blower (120 VAC)

EAC

Electronic Air Cleaner (120 VAC)

COOL

Blower - Cooling Speed (24 VAC)

HEAT

Blower - Heating Speed (24 VAC)

FAN

Blower - Fan Speed (24 VAC)

PARK

Dead terminals to park all speed taps

NEUTRALS

Neutral Terminals (120 VAC)

Flame Sense

24 COM

Common (24 VAC)

HUM 24

Humidifier (24 VAC)

Содержание GUH95C



























































Результаты поиска

Содержание GUH95C

Отзывы:

Похожие инструкции для GUH95C

Бренды по названию

Популярные бренды

COMFORT-AIRE GUH95C, Руководство по установке

Результаты поиска

Содержание GUH95C

Отзывы:

Похожие инструкции для GUH95C

Бренды по названию

Популярные бренды