background image

Installation Instructions

These instructions are primarily intended
to assist qualified individuals experienced
in the proper installation of this appliance.
Some local codes require licensed installa-
tion/service personnel for this type of equip-
ment.  Read all instructions carefully before
starting the installation.

DO NOT DESTROY.  PLEASE READ CARE-
FULLY AND KEEP IN A SAFE PLACE FOR
FUTURE REFERENCE.

*TC 92+ Upflow/Horizontal

*TL 90+ Downflow

*TC Series 92+ Upflow/Horizontal Two-Stage Condensing Furnace
*TL Series 90+ Downflow Two-Stage Condensing Furnace

Gas Fired Central Furnaces

!

 WARNING:

Improper installation, adjustment, al-
teration, service, or maintenance can
cause injury or property damage. Re-
fer to this  manual for assistance. For
additional information consult a quali-
fied installer, service agency, or  the
gas supplier.

!

 

FOR YOUR  SAFETY:

Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.

!

 

FOR YOUR  SAFETY:

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor's phone.  Follow  the
gas supplier's instructions.

• If you cannot reach your gas supplier,

call the fire department.

• Extinguish any open flame.

Summary of Contents for TC060













































Reviews: