Allied 80G1UHEX Series Installation Instructions Manual Download

Page: 1 / 32

507651-01

Issue 1907

Page 1 of 32

INSTALLATION INSTRUCTIONS

A80UH1EX & 80G1UHEX

Warm Air Gas Furnace

Upflow / Horizontal Left and Right Air Discharge

This manual must be left with the homeowner for future reference.

This is a safety alert symbol and should never be ignored. When you see this symbol on labels or in

manuals, be alert to the potential for personal injury or death.

As with any mechanical equipment, personal injury can

result from contact with sharp sheet metal edges. Be

careful when you handle this equipment.

CAUTION

Improper installation, adjustment, alteration, service

or maintenance can cause property damage, personal

injury or loss of life. Installation and service must be

performed by a licensed professional installer (or

equivalent), service agency or the gas supplier.

WARNING

Manufactured By

Allied Air Enterprises LLC

A Lennox International, Inc. Company

215 Metropolitan Drive

West Columbia, SC 29170

(P) 507651-01

*P507651-01*

Table of Contents

Unit Dimensions ..........................................................

A80UH1EX & 80G1UHEX Gas Furnace .....................

Shipping & Packing List ...............................................

Safety Information .......................................................

General ........................................................................

Combustion, Dilution & Ventilation Air .........................

Setting Equipment .......................................................

Filters .........................................................................

Duct System ..............................................................

Venting.......................................................................

Gas Piping

.................................................................

Electrical ....................................................................20

Unit Start-Up ..............................................................

Heating Sequence of Operation ...............................26

Gas Pressure Adjustment ..........................................26

Other Unit Adjustments..............................................

Blower Performance ..................................................29

Service.......................................................................

Repair Parts List ........................................................

Summary of Contents for 80G1UHEX Series

































Search results

Summary of Contents for 80G1UHEX Series

Reviews:

Related manuals for 80G1UHEX Series

Brands by name

Popular brands

Allied 80G1UHEX Series, Installation Instructions Manual

Search results

Summary of Contents for 80G1UHEX Series

Reviews:

Related manuals for 80G1UHEX Series

Brands by name

Popular brands