ComAp intelilite nt amf20 Скачать руководство пользователя

Страница: 7 / 145

InteliLite

– AMF20/25, SW version 2.2, ©ComAp – September 2014

IL-NT-AMF-2.2-Reference Guide.pdf

General Description

Description of the controller system (with all options)

InteliLite

AMF20/25 is a comprehensive AMF-controller for single generating sets operating in stand-

by mode. IL-NT AMF25 features extended support of electronic engines and extension modules.
InteliLite

controllers are equipped with a powerful graphic display showing icons, symbols and bar-

graphs for intuitive operation, which sets, together with high functionality, new standards in Gen-set
controls.
InteliLite

automatically starts the Gen-set, closes the Gen-set C.B. when all conditions are met, then

stops the engine on external signal or by pressing push buttons.
InteliLite

provides gas engine support without ventilation.

The key feature of InteliLite

is its easy-to-use operation and installation. Predefined configurations

for typical applications are available as well as user-defined configurations for special applications.

What is in the package?

Accessories

Description

Optional / Obligatory

IL-NT AMF

InteliLite

central unit

Obligatory

IL-NT-RS232

RS232 communication card

Optional for AMF20/25

IL-NT-RS232-485

RS232 and RS485 communication card

Optional for AMF20/25

IL-NT-S-USB

Service USB communication card

Optional for AMF20/25

IB-Lite

Ethernet communication card

Optional for AMF20/25

IL-NT-GPRS

GSM/GPRS modem card

Optional for AMF20/25

IL-NT-AOUT8

Gauge driver plug-in card

Optional for AMF20/25

IL-NT-BIO8

Configurable I/O plug-in card

Optional for AMF20/25

IC-NT-CT-BIO7

Configurable I/O plug-in card with earth
fault current measurement

Optional for AMF20/25

**IL-NT RD

Remote display software

Optional for AMF20/25

IGL-RA15

Remote annunciator

Optional for AMF25

IG-IOM/PTM

I/O extension module

Optional for AMF25

IG-IB

Internet communication bridge

Optional for AMF20/25

InternetBridge-NT External communication module

Optional for AMF20/25

AT-LINK-CONV

Service programming RS232 interface

Optional for AMF20/25

AT-LINK-CABLE

Serial RS232 communication cable 1,8m Optional for AMF20/25

**Remote display for IL-NT controllers uses standard IL-NT controller with Remote
display software

Hint:

For detailed information about extension modules used with IL-NT controllers, please see the IL-NT-
Accessory Modules manual.

IL-NT RS232 Communication plug-in card

IL-NT RS232 is optional plug-in card to enable InteliLite

for RS 232 communication. This is required

for computer or Modbus connecting. Card inserts into expansion slot back on the controller.

Содержание intelilite nt amf20


















































































































































Результаты поиска

Содержание intelilite nt amf20

Отзывы:

Похожие инструкции для intelilite nt amf20

Бренды по названию

Популярные бренды

ComAp intelilite nt amf20, Справочное руководство

Результаты поиска

Содержание intelilite nt amf20

Отзывы:

Похожие инструкции для intelilite nt amf20

Бренды по названию

Популярные бренды