background image

Page  10

Section 3:  Operation

NOTE:  If the changer LO-$.25 option switch is set

to the on position, accepted quarters will be routed to

the cash box when the (middle $.25 tube sensor) is

blocked by coins.

CHANGE  PAYBACK

The low tube sensors report which coins are

available for payback so payout can be made in the

fewest coins available.

EXACT CHANGE CONDITION

The microprocessor is constantly looking at the

change status.  If correct change cannot be made,

the changer rejects the last coin deposited, resulting

in an over insertion.  At this time, the correct change

light flashes on and off in one second intervals for 10

seconds, during which time the escrow lever may be

depressed for a full refund, the correct change my be

inserted or the same coin which was rejected may be

reinserted.  (However, no change payout will be

attenped under this condition.)  If correct change

cannot be made for a dollar bill, the correct change

light will be lit continuously, inhibiting the bill

validator.

COIN  PAYOUT

The payout assembly pays out coins using three

solenoid-operated slides.  Coins are paid out for:

change payout, escrow return and manual inventory

of the coin tubes.
When a solenoid energizes, the upward motion of its

plunger compresses a spring and draws the soenoid

lever, which in turn pushes a payout slide forward.

This loads the coin for payout.  When the solenoid

de-energizes, the spring force returns the plunger to

its de-energized state, which returns the solenoid

lever and payout slide, dispensing a coin.  Payout

rate is two coins per second.
Change Payout:  When the amount of credit exceeds

the vend price, a payout will be made in the least

number of available coins.  (See Exact Change

Condition.)

Escrow Return:  When a request for escrow is

made, the changer will return the amount credited in

the least number of coins.  Under exact change

conditions, nickles, dimes and quarters may be

returned coin for coin.
Manual Inventory of Coins:  Operating the manual

inventory switches manually empties the changer

coin tubes.  The inventory switches are located on

the front of the inventory tube assembly.  Only one

inventory switch will operate at a time.

DOLLAR  CREDIT  ESCROW

Credit from the dollar bill validator or dollar coin is

not inhibited from escrow.  Four quarters will be

returned to the customer if an escrow is called for.

ESCROW

Escrow Until Vend:  Allows the customer to get a

full refund any time before actual vend price is

reached.
Escrow Until Select:  Allows the customer to receive

a full refund any time prior to product delivery.

NOTE:

  Then vendor circuit determines whether the

escrow to select feature can be used.

Содержание 9300-S Series





























Отзывы: