background image

1

New Product

Easy to Use and Easy to Read.

Basic Features

• Character height of 10 mm for better readability.
• Operation is simplified by the Up Key for each digit.

Safety and Reliability

• Power supply circuit and input circuits are isolated inside the 

Counter.

• Set value limit function prevents unexpected operation of output 

devices caused by setting mistakes.

• Output counter function helps in managing the service life of the 

Counter or the load.

Other Features

• Waterproof, dust-proof structure (UL508 Type 4X and IP66).
• Key protection.

Features

Basic Features

Better Readability

Character Height of 10 mm with a Wide Viewing Angle.

The Easiest Operation

Operation is simplified by the Up Key for 
each digit.

Safety and Reliability 

Isolated Power Supply and Input Circuits

Power supply circuit and input circuits are isolated inside the Counter. 
Previous non-isolated counters had wiring restrictions and could be 
damaged if wired incorrectly. The H7CZ removes these worries.

Set Value Limit

You can set an upper limit for the set value to prevent unexpected 
operation of output devices caused by setting mistakes. 

Output Counter

The output counter counts the number of times the output turns ON 
(alarms can be displayed and the count can be monitored in 
increments of 1,000 operations). This counter is useful in managing 
the service life of the Counter or the load. 

Other Features

Waterproof, Dust-proof Structure (UL508 Type 
4X and IP66)

Worry-free application is possible in locations subject to water.

Note:

When the Y92S-29 Waterproof Packing is used.

Key Protection 

Select from any of seven protection patterns. Use the best one for the 
application.

Refer to 

Safety Precautions

 on page 17.

For the most recent information on models that have been certified for 
safety standards, refer to your OMRON website.

10 mm

(act

u

al size)

Clear 

Confirmation

Easy to read from the top, 

b

ottom, and sides.

For 1,000 pieces

N

o o

v

erflo

w

Setting the 

u

pper limit of the set 

v

al

u

e ena

b

les 

w

orry-free operation. 

Digital Counter

H7CZ

Содержание H7CZ Series





















Отзывы: