Coemar CF 1200 Spot Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 30

background image

protection

The unse of s thermal magnetic circuit breaker is recommended for each

CF 1200

Spot

.

A good earth connection is essential for the correct operation of the fixture. Strict
adherance to regulatory norms is strongly recommended.

ATTENTION!, DANGER!

The electronic ballast with which the

CF 1200 Spot

is fitted, as with other electro-

nic devices, requires a correct dimension for the neutral conductor, since the current
in the neutral conductor is equal to the sum of the current in all the active conduc-
tors.
For example, if at the mains outlet a current of 10Amps is on phase R, 10Amps on
phase S, and 10Amps on phase T, a total current of 30 Amps exists in the netural.
Please note the above to ensure the correct selection of cable dimensions. Qualified
electrical personnel should always be consulted.

CF 1200 Spot

requires a proper earth connection to operate

safely and correctly. Never operate the fixture unless the

green/yellow conductor is connected

.

«
...
9
10
11
12
13
...
»

Содержание CF 1200 Spot































Отзывы:

Нет отзывов

Похожие инструкции для CF 1200 Spot

Бренд: Landoll Страницы: 34

Бренд: Bante Instruments Страницы: 6

Бренд: Rane Страницы: 38

Бренд: Kartsana Страницы: 36

Бренд: Raven Страницы: 48

Бренд: Pacific Страницы: 16

MCX-C15 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 65

Бренд: Yamaha Страницы: 24

Бренд: Panasonic Страницы: 23

Бренд: Öhlins Страницы: 8

Бренд: &Tradition Страницы: 3

Flowerpot VP3 Verner Panton 1968

Бренд: &Tradition Страницы: 3

Бренд: ?HC Страницы: 2

FLOWERPOT GARDEN VP5

Бренд: &Tradition Страницы: 4

FLOWERPOT GARDEN VP3

Бренд: &Tradition Страницы: 4

Бренд: &Tradition Страницы: 4

MIAMI J ADVANCED

Бренд: Össur Страницы: 35

Бренд: Össur Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды