CLIVET WSAT-XSC3 260.6-480.8 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 76

background image

4

WSAT-XSC3 260.6-480.8

M08T40D16-02

1 General description

1.1 Manual

The manual provides correct unit installation, use and maintenance.
Pay particular attention to:

Warning, identifies pa ticularly important operations or information.

Prohibited operations that must not be carried out, that compromise the operating of the unit or may cause damage to persons or things.

•

It is advisable to read it carefully so you will save time during operations.

•

Follow the written indications so you will not cause damages to things and injuries people.

1.2 Preliminaries

Only qualified personnel can ope ate on the unit, as required by the regulation in force.

1.3 Risk situations

The unit has been designed and created to prevent injures to people.

During designing it is not possible to plane and operate on all risk situation.
Read carefully “Residual risk” section where all situation which may cause damages to things and injuries to people are reported.
Installation, starting, maintenance and repair required specific knowledge; if they are carried out by inexperienced personnel, they may cause

damages to things and injuries people.

1.4 Intended use

Use the unit only:

•

for cooling/heating water or a water and glycol mix

•

keep to the limits foreseen in the technical schedule and in this manual

The manufacturer accepts no responsibility if the equipment is used for any purpose other than the intended use.

1.5 Installation

Outdoor installation

The positioning, hydraulic system, refrigerating, electrics and the ducting of the air must be determined by the system designer in accordance

with local regulations in force.
Follow local safety regulations.
Verify that the electrical line characteristics are in compliance with data quotes on the unit serial number label.

1.6 Maintenance

Plan periodic inspection and maintenance in order to avoid or reduce repairing costs.

Turn the unit off be ore any operation.

1.7 Modification

All unit modific tions will end the warranty coverage and the manufacturer responsibility.

1.8 Breakdown/Malfuction

Disable the unit immediately in case of breakdown or malfunction.
Contact a certified se vice agent.
Use original spares parts only.
Using the unit in case of breakdown or malfunction:

•

voids the warranty

•

it may compromise the safety of the unit

•

may increase time and repair costs

«
...
2
3
4
5
6
...
»

Содержание WSAT-XSC3 260.6-480.8













































































Отзывы:

Нет отзывов

Похожие инструкции для WSAT-XSC3 260.6-480.8

Бренд: Tar River Страницы: 68

Бренд: Poulan Pro Страницы: 24

CenTraVac CDHF Series

Бренд: Trane Страницы: 104

Бренд: Gree Страницы: 58

Бренд: Laski Страницы: 47

Бренд: Instanta Страницы: 7

Бренд: Texas Страницы: 54

Бренд: Polar Refrigeration Страницы: 40

Бренд: Elkay Страницы: 4

Бренд: Agrisem Страницы: 54

45 COMBISET BLAST CHILLER

Бренд: Fulgor Milano Страницы: 192

Бренд: Jonsered Страницы: 40

Бренд: Weed Eater Страницы: 24

Бренд: Weed Eater Страницы: 24

Бренд: Wallenstein Страницы: 68

Бренд: Land Pride Страницы: 18

Бренд: Garland Страницы: 180

Бренд: Elkay Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды