CLIVET WSAT-XSC3 260.6-480.8 Скачать руководство пользователя страница 18

Страница: 18 / 76

WSAT-XSC3 260.6-480.8

M08T40D16-02

5.10 Modbus - RS485

Option

LED BSP

communication with AP1 module

LED BUS

communication with Modbus

green

communication ok

green

communication ok

yellow

software ok but communication with AP1

down

yellow

startup / channel not communicating

red

flashing: software error

red

communication down

fixed: hardware error

A.   Unit
B.   Metal conduit
C.   Metal septums
D.   Metal-lined sheath (sleeve)

Modbus / LonWorks / Cable requirements

Couple of conductors twisted and shielded
Section of conductor 0,22mm2…0,35mm2
Rated power between conductors < 50 pF/m
Nominal impedance 120 Ω
Recommended cable BELDEN 3106A

•

Every RS485 serial line must be set up using the ‘In/Out’ bus system.

•

Other types of networks are not allowed, such as Star or Ring networks.

•

The

diff

erence in potential between the earth of the two RS485 devices that the cable shielding needs to be connected to must be lower

than 7 V

•

There must be suitable arresters to protect the serial lines fr

om the eff

ects of atmospheric discharges

•

A 120 ohm resistance must be located on the end of the serial line. Alternatively, when the last serial board is equipped with an internal

terminator, it must be enabled using the specific jumpe , dip switch or link.

•

The cable must have insulation features and non-flame p opagation in accordance with applicable regulations.

•

The RS485 serial line must be kept as far away as possible from sources of electromagnetic interference.

Содержание WSAT-XSC3 260.6-480.8













































































Результаты поиска

Содержание WSAT-XSC3 260.6-480.8

Отзывы:

Похожие инструкции для WSAT-XSC3 260.6-480.8

Бренды по названию

Популярные бренды

CLIVET WSAT-XSC3 260.6-480.8, Инструкция по установке и эксплуатации

Результаты поиска

Содержание WSAT-XSC3 260.6-480.8

Отзывы:

Похожие инструкции для WSAT-XSC3 260.6-480.8

Бренды по названию

Популярные бренды