Clifford Level Four, Руководство по установке

Страница: 11 / 16

User-Selectable Features (Customer Mode): 1 beep = OFF, 2 beeps= ON
Feature
Select
Right x 1 Right x 2 Right x 3 Right x 4
Left x
1
Add a new remote
NOTE 1
Chirps*/beeps:
off**/ on /quiet
(1/ 2 /3
chirps*/beeps)
AutoArming:
off /on**
NOTE 5 — Other remote:
arm (1 then 2 beeps)
Left x
2
Personalized Siren
Sounds*
NOTE 2
NOT USED
Lock upon
AutoArming:
off /on**
NOTE 6 — Other remote:
trunk release (2 beeps)
Left x
3
Play Siren Sounds*:
trigger only/ always
(1/ 2 beeps)
NOT USED
AutoArming
entry delay:
off /on
NOTE 6 — Other remote:
panic (3 beeps)
Left x
4
Siren duration:
30 /60/90sec.
( 1 /2/3 beeps)
AutoStart*: both
off /both on/temp
only/battery only
( 1 /2/3/4 beeps)
FACT: off/ on
NOTE 6 — Other remote:
disarm (4 beeps)
Left x
5
AutoLock: off/ on /rpm*
(1/ 2 /3 beeps)
NOT USED NOT USED
NOTE 6 — Other remote:
remote starting* (5 beeps)
Left x
6
AutoUnLock: off/ on
Clear all remotes
NOTE 3
NOT USED
NOTE 6 — Other remote:
window rolldown/venting*
(6 beeps)
Left x
7
Reset all features to
default (except
remotes & valet code)
Set a new secret
valet code
NOTE 4
NOT USED
NOTE 6 — Other remote:
valet mode (7 beeps)
* Requires optional G4 accessory
** In Dealer Mode (see page 3), beeps/chirps are off; AutoArming and Lock upon AutoArm are on
n
NOTE 1: Press the lock button of the new vehicle buyer’s remote. You’ll hear one beep. Press the
lock button again. You’ll hear two beeps to confirm that the new remote control has been added.
n
NOTE 2: If equipped with the optional Self-Powered SmartSiren 4, selection of this feature will
cause the system to sound a few seconds of siren sound #1. Toggle the valet switch to the right to
turn on this sound or to the left to turn it off. The system will then sound a few seconds of sound
#2. Repeat: right=ON, left=OFF for each of the six sounds.
n
NOTE 3: Two beeps indicate all remotes have been cleared from memory. You must now add
new/existing remotes with the “Add new remote” feature and/or the “Other remote” feature.
n
NOTE 4: Immediately toggle to the right, then enter the new code, wait for the two beeps, then
turn off the ignition (you’ll hear 3 beeps to confirm program mode exit). You MUST now turn the
ignition back on and then re-enter the new code. If the LED flashes on, the new code is set. If the
LED does not light, the two codes did not match and the system has reverted to the previous code.
n
NOTE 5: Permits arming with the remote of a G4 system on another vehicle. For example, to set the
✱ button of the other car’s remote to arm this system, select column 4, row 1, then press the ✱
button of the other car’s remote (you’ll hear one beep). Immediately press the
✱
button again (two
beeps). The ✱ button of the other remote will now arm this system. Then select row 4 of this same
column to assign a different button to disarm.
n
NOTE 6: The features in this column allow control of the system with the remote of a G4 system
on another vehicle. Select the function, then press the unused button or button combination on
the other remote that you want to use to perform that function on this system (you will then hear a
the beeps noted). NOTE: You must first set a button or button combination on the other car’s
remote that will arm the system (column 4, row 1) before these others will be accepted.
9
11
D:...-922 Level 4 install manual.vp
Wed Aug 04 17:37:20 1999
Color profile: Disabled
Composite Default screen