Clifford Level Four, Руководство по установке

Страница: 12 / 16

Installer-Programmable Features
1. Turn on the ignition.
2. Enter the factory preset valet/programming code of “2” by toggling the valet switch
(located behind the LED assembly) to the left two times, then to the right.
3. Hold the switch to the left. You’ll hear one beep after about 3 seconds to indicate user
programming mode. KEEP HOLDING (about 12 more seconds) until you hear the
3-beep installer programming mode confirmation.
4. Select the feature column: Toggle the switch to the right the number of times indicated
for the column. Pause. You will hear the same number of horn beeps, confirming your
selection.
5. Within five seconds, select the feature row: Toggle the switch to the left the number of
times indicated for the row. You’ll hear a beep each time to help you count.
6. If there is a NOTE for the selected feature, perform the actions noted.
7. Pause. You will hear either one or two beeps: two beeps = ON, one beep = OFF.
8. You can select another feature, or you can exit program mode:
a. To select another feature in that same column, repeat step 5 within the next five
seconds (after five seconds, three beeps indicate return to the “ Feature Select ” position).
b. To select a different feature column, repeat step 4.
c. To exit program mode, turn the ignition off (you’ll hear three beeps and the LED will
turn off), or wait 60 seconds for the system to automatically exit program mode.
Installer-Programmable Features: 1 beep = OFF, 2 beeps = ON
Feature
Select
Right x 1 Right x 2 Right x 3
Left x
1
Single /Double
Lock Pulse
( 1 beep /2 beeps)
Accessory Output Timer
Duration ( 10sec. ): 1-255
sec. NOTE B
Door Ajar Warning
/Delayed Courtesy Lights
( 1 beep /2 beeps)
Left x
2
Single /Double Unlock Pulse
( 1 beep /2 beeps)
Accessory Output B type:
( Pulsed /Timed/Latched)
( 1 beep /2 beeps/3 beeps)
Accessory Output A
Trunk Interlock
( On /Off)
Left x
3
Lock/Unlock Pulse:
1 second/ 3 second
( 1 beep /2 beeps)
NOT USED
Accessory Output A for
2-Stage Unlocking
(pgs 5 & 10) (On/ Off )
Left x
4
NOT USED
IntelliStart 4: Diesel/ Gas
(1 beep/ 2 beeps )
Accessory Output B
Trunk Interlock
(On/ Off )
Left x
5
IntelliStart 4: Program RPM
NOTE A
Program Optional
SmartWindows 4 NOTE C
AutoActivate Accessory
Output B Upon Remote
Arming (On/ Off )
Left x
6
Car Horn /Optional Siren
( 1 beep /2 beeps)
Sleep Mode (only if in
dealer mode, see page 3)
(On/ Off )
NOT USED
n
NOTE A: Please note that the Diesel/Gas selection (column 2, row 4) must be made before
programming RPM. To program RPM, the engine must be running at its normal idle speed when
you select this feature. Two beeps and two parking light flashes confirm RPM programming, two
beeps and one parking light flash indicates no tach signal, check the BLACK/GRAY wire
connection.
n
NOTE B: A chirp will indicate the timer has started. When the desired duration has been reached
(1-255 seconds), tap the valet switch to the right (2 chirps).
n
NOTE C: You will hear two beeps. Press and hold the driver’s window switch in the up position for
2 seconds, then release. The windows will close and open repeatedly. Programming is complete
when the windows vent. For a second SmartWindows 4 module, briefly tap the driver’s window
switch up to repeat the process for the rear windows.
10
12
D:...-922 Level 4 install manual.vp
Wed Aug 04 17:37:22 1999
Color profile: Disabled
Composite Default screen