background image

Fi nal Wir ing Con nec tions

1. Connect the RED wire to the 5A fuseholder as shown on page 4. 

2. Connect the RED/WHITE wire to the 20A fuseholder as shown on page 4.

3. Attach the two fuseholders to the battery positive cable clamp.

4. Attach the BLACK wire to the vehicle battery negative cable clamp. 

NOTE: Power and test ac ces so ries af ter the ba sic sys tem has been tested.

In di vidu ally fuse all ac ces sory power con nec tions. In di vidu ally fuse all +12V 

con nec tions.

Smart Powe rUp™ 2

SmartPowerUp 2 ensures that the system powers up in the same state (disarmed, armed or valet

mode) it was last in. When you first power up the system, it will silently enter its disarmed state. 

De layed Cour tesy Lights

Some vehicles have a courtesy light delay or dimming circuit, which interferes with an alarm being

able to detect the door trigger upon remote arming. If the delay or dimming lasts more than 5

seconds, no special connections or testing are needed, simply turn on the 

Delayed Courtesy Lights

feature as noted in the 

Installer-Programmable Features

 

section on page 16. Please note that

since this feature sets the system to arm the instant the courtesy lights are off, the Door Ajar

Warning feature will not be available.

Re mote Con trol Button As sign ments

The Cyber 4 comes with two ergonomically designed remote controls. Up to two additional

Clifford ACG 2 remote controls can be added (older Clifford ACG and non-ACG remotes

are not compatible with the Cyber 4). For instructions on how to use the remote controls,

please refer to the Cyber 4 User’s Manual.

12

Func tion

Press but ton(s)

Arm/Disarm

Activate Auxiliary A* 

(usually remote trunk release)*

Silent Arm/Disarm

 + 

IntelliStart 4 Accessory*

Activate Auxiliary B* 

(usually timed headlight activation)

SmartWindows 4 Accessory*

 + 

Unassigned*

 + 

Unassigned*

 + 

Remote Valet Mode Enter/Exit*

 + 

LowTemp/LowBattery AutoStart or

Manual Transmission SafeStart*

 + 

*These chan nels can be as signed to con trol other Clif ford ACG 2 sys tems

and ac ces so ries on the cus tomer’s other ve hi cles.

Содержание Cyber 4

























Отзывы: