Clarion Ungo ProSecurity RS10 Скачать руководство пользователя страница 7

Страница: 7 / 41

5. Cut the wire you suspect of being the starter wire.

6. Attempt to start the car. If the starter engages, reconnect it and go back to Step 3. If the starter does not

turn over, you have the right wire.

The ignition wire is powered when the key is in the run or start position. This is because the ignition wire powers

the ignition system (spark plugs, coil) as well as the fuel delivery system (fuel pump, fuel injection computer).

Accessory wires lose power when the key is in the start position to make more current available to the starter motor.

How to find (+)12V ignition with your multimeter:

1. Set to DCV or DC voltage (12V or 20V is fine).

2. Attach the (-) probe of the meter to chassis ground.

3. Probe the wire you suspect of being the ignition wire. The steering

column harness or ignition switch harness is an excellent place to find

this wire.

4. Turn the ignition key switch to the run position. If your meter reads

(+)12V, go to the next step. If it does not read (+)12V, probe another wire.

5. Now turn the key to the start position. The meter display should stay

steady, not dropping by more than a few tenths of a volt. If it drops close

to or all the way to zero, go back to Step 3. If it stays steady at (+)12V, you have found an ignition wire.

An accessory wire will show (+)12V when the key is in the accessory and run positions. It will not show (+)12V

during the cranking cycle. There will often be more than one accessory wire in the ignition harness. The correct

accessory wire will power the vehicle's climate control system. Some vehicles may have separate wires for the

blower motor and the air conditioning compressor. In such cases, it will be necessary to add a relay to power the

second accessory wire.

finding the accessory wire

finding the 12V switched ignition wire

Содержание Ungo ProSecurity RS10





































Результаты поиска

Содержание Ungo ProSecurity RS10

Отзывы:

Похожие инструкции для Ungo ProSecurity RS10

Бренды по названию

Популярные бренды

Clarion Ungo ProSecurity RS10, Руководство по установке

Результаты поиска

Содержание Ungo ProSecurity RS10

Отзывы:

Похожие инструкции для Ungo ProSecurity RS10

Бренды по названию

Популярные бренды