Clarion Ungo ProSecurity RS10 Скачать руководство пользователя

Страница: 21 / 41

bypassing GM vehicle anti-theft systems (VATS)

Vehicles with the GM VATS (Pass Key) systems have a resistor embedded in the ignition key. If the VATS decoder

module does not measure the proper resistance when the vehicle is started, the starter and fuel pump may be dis-

abled for up to ten minutes. An optional "VATS pack" of resistors is available

(p/n 652T)

. One of the resistors in the

pack will match the resistor in the key.

The VATS wires will be two very light-gauge wires coming out of the steering column. The colors of the wires vary,

but they are often contained in orange tubing - either both will be white wires, or one wire will be purple/white

and the other white/black. Determine the value of the resistor in the key. Then follow the diagram below to

bypass VATS during remote engine start operation. If the BLUE status output from the relay satellite has been

programmed for factory security re-arm, then use the (H3/5) BLUE/WHITE 2

status output from the control

module to control the relay.

NOTE:

When connecting to the VATS wires, it is not important which wire is cut.

BLUE OR

BLUE/WHITE

(+) 12V CONSTANT FUSED

87 87A

TO IGNITION KEY SWITCH

CUT

PROPER RESISTOR VALUE

TO VATS DECODER MODULE

WHITE

WHITE/BLACK

WHITE

PURPLE/WHITE

Содержание Ungo ProSecurity RS10





































Результаты поиска

Содержание Ungo ProSecurity RS10

Отзывы:

Похожие инструкции для Ungo ProSecurity RS10

Бренды по названию

Популярные бренды

Clarion Ungo ProSecurity RS10, Руководство по установке

Результаты поиска

Содержание Ungo ProSecurity RS10

Отзывы:

Похожие инструкции для Ungo ProSecurity RS10

Бренды по названию

Популярные бренды