Clarion Ungo ProSecurity RS10 Скачать руководство пользователя страница 30

Страница: 30 / 41

features menu

The factory default settings are indicated in

bold

text in the table below.

FEATURE

DEFAULT - LED ON SETTING

LED OFF SETTING

NUMBER

(PRESS CHANNEL 1)

(PRESS CHANNEL 2)

Engine checking on

Engine checking off

Tachometer checking type

Voltage checking type

12 minutes run time

(1)

24 minutes (2)*, 60 minutes (3) run time

Flashing parking light output

Constant parking light output

Cranking time 0.6 sec.

(1)

Cranking time 0.8 (2), 1.0 (3), 1.2 (4), 1.4 (5),
1.6 (6), 1.8 (7), 2.0 (8), 4.0 (9) sec.

Voltage check high level

Voltage check low level

Short Run (turbo timer): 1

(1)

min

Short Run (turbo timer) 3 (2), 5 (3), 10 (4) min.

Activation pulse: 1 (1)

Activation pulses: 2

(2), 3 (3)

Ignition/accessory output: Ignition

Ignition/accessory output: Accessory

Accessory state during wait to start: OFF

Accessory state during wait to start: ON

2nd status output: Normal

(1)

Rear defogger latched (2)/pulsed (3)

Diesel timer Wait-to-Start input

(1)

Timed 15 (2), 30 (3), 45 (4) seconds

Run Time (Timer Mode) 12 minutes

(1) 3 (2), 6 (3), 9 (4) minutes

Door Lock pulse duration 0.8 seconds

(1)

3.5 (2), 0.4 (3) seconds

Unlock output 1 pulse

Unlock output 2 pulses

Lock output 1 pulse

Lock output 2 pulses

Ignition unlock ON

Ignition unlock OFF

Ignition lock ON

Ignition lock OFF

Factory Alarm Disarm with unlock

Before Unlock (2)/remote engine start only (3)

Factory Alarm Disarm 1 pulse

2 pulses

Comfort Closure ON

OFF

*NOTE:

The number in parentheses indicate the number of times the LED will flash

Содержание Ungo ProSecurity RS10





































Результаты поиска

Содержание Ungo ProSecurity RS10

Отзывы:

Clarion Ungo ProSecurity RS10, Руководство по установке, Страница: 30 / 41

Результаты поиска

Содержание Ungo ProSecurity RS10

Отзывы: