Clarion Ungo ProSecurity RS10 Скачать руководство пользователя страница 28

Страница: 28 / 41

tach learning

Start the vehicle with the key.

Within 5 seconds, press and

HOLD

the Program switch.

The LED will light constant when the tach signal is learned.

Release the Program switch.

operating settings learn routine

The System Features Learn Routine dictates how the unit operates. The programmable operating settings of this

unit can be changed whenever necessary through the computer-based Learn Routine. The Program push-button

switch, plugged into the blue port, is used together with a programmed transmitter to change the settings. It is

possible to access and change any of the feature settings using the Program switch. To program settings, remem-

ber: Key, Choose, Transmit and Release.

To program the learn routine:

Key.

Turn the ignition on and then back off.

Choose.

Within 10 seconds, press and release the Program switch the number of times cor-

responding to the feature number you want to program. (See

Features Menu

section.)

Once the Program switch has been pressed and released the desired number of times, press it once more and

HOLD

it. After a second, the LED will flash to indicate which feature you have accessed. For example, groups of

eight flashes would indicate access to the status output feature (Feature 8).

DRW-96

to learn the tach signal

Содержание Ungo ProSecurity RS10





































Результаты поиска

Содержание Ungo ProSecurity RS10

Отзывы:

Clarion Ungo ProSecurity RS10, Руководство по установке, Страница: 28 / 41

Результаты поиска

Содержание Ungo ProSecurity RS10

Отзывы: