Cisco WRP500 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 128

background image

R E V I E W D R A F T # 1 — C I S C O C O N F I D E N T I A L

A-2

Cisco WRP500 Administration Guide

Appendix A Advanced Voice Fields

Info page

Voice tab > Info page >

Product Information section

Voice tab > Info page >

System Status section

Product Name

Model number/name.

Serial Number

Serial number.

Software Version

Software version number.

Hardware Version

Hardware version number.

MAC Address

MAC address.

Client Certificate

Status of the client certificate, which can indicate if the WRP500
has been authorized by your ITSP.

Customization

For a Remote Configuration (RC) unit, this field indicates whether
the unit has been customized or not. Pending indicates a new RC
unit that is ready for provisioning. If the unit has already retrieved
its customized profile, this field displays the name of the company
that provisioned the unit.

Voice Module Version Voice module number

Current Time

Current date and time of the system; for example, 10/3/2003
16:43:00.

Elapsed Time

Total time elapsed since the last reboot of the system; for example,
25 days and 18:12:36.

RTP Packets Sent

Total number of RTP packets sent (including redundant packets).

RTP Bytes Sent

Total number of RTP bytes sent.

RTP Packets Recv

Total number of RTP packets received (including redundant
packets).

RTP Bytes Recv

Total number of RTP bytes received.

SIP Messages Sent

Total number of SIP messages sent (including retransmissions).

SIP Bytes Sent

Total number of bytes of SIP messages sent (including
retransmissions).

SIP Messages Recv

Total number of SIP messages received (including retransmissions).

«
...
44
45
46
47
48
...
»

Содержание WRP500

































































































































Отзывы:

Нет отзывов

Похожие инструкции для WRP500

DVG-G1402S - Wireless Broadband VoIP Router

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 2

Бренд: Bang & Olufsen Страницы: 9

DGL-4500 - GamerLounge Xtreme N Gaming Router...

Бренд: D-Link Страницы: 108

DAP-3520 - AirPremier N Dual Band Exterior PoE Access...

Бренд: D-Link Страницы: 38

DAP-3520 - AirPremier N Dual Band Exterior PoE Access...

Бренд: D-Link Страницы: 80

DAP-2590 - AirPremier N Dual Band PoE Access...

Бренд: D-Link Страницы: 36

Бренд: Zhone Страницы: 54

Бренд: Conrad Страницы: 8

Бренд: FIXED Страницы: 20

Бренд: MeshLinx Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды