Cisco WRP500 Скачать руководство пользователя страница 118

Страница: 118 / 128

R E V I E W D R A F T # 1 — C I S C O C O N F I D E N T I A L

B-28

Cisco WRP500 Administration Guide

Appendix B Data Fields

Status

Status > Local Network

Status > Wireless Network

Card Model

The model number of your Mobile USB modem data
card.

Card Firmware

The firmware that is installed on your Mobile USB
modem data card.

SIM Status

The status of your SIM card.

IMSI

International Mobile Subscriber Identity is a unique
number that is stored in the Subscriber Identity Module
(SIM) associated with all GSM and Universal Mobile
Telecommunications System (UMTS) network mobile
phone users.

Carrier

The network service provider that is used for Internet
connection.

Service Type

The current UMTS/GPRS/EVDO service for Internet
connection.

Signal Strength

The signal strength of your current
UMTS/GPRS/EVDO service to your location.

Card Status

The current Mobile WAN connection status.

Local Network

Local MAC Address

The MAC address of the local, wired interface of the
WRP500 is displayed.

Router IP Address

The IP address of the WRP500, as it appears on your
local network, is displayed.

Subnet Mask

The Subnet Mask of the WRP500 is displayed.

DHCP Server

DHCP Server

The status of the DHCP server function.

Start IP Address

The starting IP address for the range of IP addresses
used by devices on your local network.

End IP Address

The ending IP address for the range of IP addresses
used by devices on your local network.

Channel

The channel used by the wireless network(s) .

Содержание WRP500

































































































































Результаты поиска

Содержание WRP500

Отзывы:

Похожие инструкции для WRP500

Бренды по названию

Популярные бренды

Cisco WRP500, Руководство администратора

Результаты поиска

Содержание WRP500

Отзывы:

Похожие инструкции для WRP500

Бренды по названию

Популярные бренды