Cisco WRP500 Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 128

background image

R E V I E W D R A F T # 1 — C I S C O C O N F I D E N T I A L

B-10

Cisco WRP500 Administration Guide

Appendix B Data Fields

Setup

Card Model

The data card model that is inserted in the USB port.

Carrier

The mobile network service provider for Internet
connection. This setting is required when you are using
HSDPA/UMTS/GPRS Internet service.

Country

The card issue country

Carrier

The card issue provider

Access Point Name (APN)

The name that the mobile network service provider has
assigned to the particular Internet network for this
connection.

Dial Number

The dial number that is used to access the mobile
network service.

User Name and Password
(Optional)

The user name and password, if any, provided by your
mobile network service provider.

SIM PIN (Optional)

The PIN code associated with your SIM card, if
required.

Server Name (Optional)

The name of the server for the Internet connection, if
required.

Authentication

The type of authentication used by your service
provider.

Default: Auto

Service Type

The most commonly available type of mobile data
service connection based on your area service signal. If
your location supports only one mobile data service,
you may set up for enhance build up connection. The
first selection will always search for
HSPDA/3G/UMTS service or switch to GPRS
automatically only when it is available.

«
...
98
99
100
101
102
...
»

Содержание WRP500

































































































































Отзывы:

Нет отзывов

Похожие инструкции для WRP500

Бренд: Nexxt Страницы: 2

Skyr@cer USB 4101GMR

Бренд: Topcom Страницы: 212

Verizon Jetpack AC791L

Бренд: NETGEAR Страницы: 2

Бренд: Digi Страницы: 9

AirStation Draft-N WZR-G300N

Бренд: Buffalo Страницы: 12

MSM-802.11 series

Бренд: HP Страницы: 32

Бренд: HP Страницы: 12

Бренд: i-MO Страницы: 18

Бренд: EnGenius Страницы: 2

Бренд: EnGenius Страницы: 64

WatchDog 3388BC

Бренд: Spectrum Technologies Страницы: 10

Бренд: Sierra Wireless Страницы: 62

AirPrime AR7558

Бренд: Sierra Wireless Страницы: 60

Бренд: Sierra Wireless Страницы: 69

Бренд: CAMBRIDGE Страницы: 12

Бренд: Planex Страницы: 83

Бренд: Zio Страницы: 69

Бренд: Sapido Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды