manualshive.com logo in svg

Cisco 3750 - Catalyst EMI Switch, Руководство по установке оборудования

Поделиться
Скачать
Cisco 3750 - Catalyst EMI Switch Скачать руководство пользователя страница 66

 

Chapter 2      Product Overview

Front Panel Description

2-18

Catalyst 3750 Switch Hardware Installation Guide

78-15136-03

Even if PoE mode is not selected on a Catalyst 3750-24PS or 3750-48PS switch, 
the PoE LED still shows PoE problems when they are detected.

Table 2-5

 lists the PoE mode LED colors and their meanings. 

Table 2-4

Port Mode LEDs

Mode LED

Port Mode

Description

STAT

Port status

The port status. This is the default mode.

DUPLX 

Port duplex mode

The port duplex mode: full duplex or half duplex.

Note

The 10/100/1000 ports operate only in full-duplex 
mode.

SPEED

Port speed

The port operating speed: 10, 100, or 1000 Mbps.

STACK 

Stack member status

StackWise port status

The stack member status.

The StackWise port status. See the 

“Stack LED” section on 

page 2-21

 for more information.

PoE

1

1.

The PoE LED is only on the Catalyst 3750-24PS and 3750-48PS switches.

10/100 PoE port power

The PoE status.

Table 2-5

PoE Mode LED

Color

PoE Status

Off

PoE mode is not selected. None of the 10/100 ports have been denied power or are 
in a fault condition.

Green

PoE mode is selected, and the PoE status is shown on the port LEDs. 

Blinking amber

PoE mode is not selected. At least one of the 10/100 ports has been denied power, 
or at least one of the 10/100 ports has a PoE fault.

Содержание 3750 - Catalyst EMI Switch







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды