manualshive.com logo in svg

Cisco 3750 - Catalyst EMI Switch, Руководство по установке оборудования

Поделиться
Скачать
Cisco 3750 - Catalyst EMI Switch Скачать руководство пользователя страница 134

 

Chapter 3      Switch Installation

Connecting to an SFP Module

3-56

Catalyst 3750 Switch Hardware Installation Guide

78-15136-03

Connecting to a Fiber-Optic SFP Module

Follow these steps to connect a fiber-optic cable to an SFP module:

Caution

Do not remove the rubber plugs from the SFP module port or the rubber caps from 
the fiber-optic cable until you are ready to connect the cable. The plugs and caps 
protect the SFP module ports and cables from contamination and ambient light.

Before connecting to the SFP module, be sure that you understand the port and 
cabling stipulations in 

“Installation Guidelines” section on page 3-7

 and in the 

“SFP Module Slots” section on page 2-12

. See 

Appendix B, “Connector and 

Cable Specifications”

 

for information about the LC on the SFP module.

Step 1

Remove the rubber plugs from the module port and fiber-optic cable, and store 
them for future use. 

Step 2

Insert one end of the fiber-optic cable into the SFP module port (see 

Figure 3-46

).

Step 3

Insert the other cable end into a fiber-optic receptacle on a target device.

Step 4

Observe the port status LED.

The LED turns green when the switch and the target device have an established 
link.

The LED turns amber while the STP discovers the network topology and searches 
for loops. This process takes about 30 seconds, and then the port LED turns green.

If the LED is off, the target device might not be turned on, there might be a cable 
problem, or there might be problem with the adapter installed in the target device. 
See 

Chapter 4, “Troubleshooting,”

 for solutions to cabling problems.

Содержание 3750 - Catalyst EMI Switch







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды