manualshive.com logo in svg

Cisco 3750 - Catalyst EMI Switch, Руководство по установке оборудования

Поделиться
Скачать
Cisco 3750 - Catalyst EMI Switch Скачать руководство пользователя страница 137

 

3-59

Catalyst 3750 Switch Hardware Installation Guide

78-15136-03

Chapter 3      Switch Installation

Connecting to a XENPAK Module

The LED turns amber while the STP discovers the network topology and searches 
for loops. This process takes about 30 seconds, and then the port LED turns green.

If the LED is off, the target device might not be turned on, there might be a cable 
problem, or there might be problem with the adapter installed in the target device. 
See 

Chapter 4, “Troubleshooting,”

 for solutions to cabling problems.

Step 4

If necessary, reconfigure and restart the switch or target device.

Connecting to a XENPAK Module

Follow these steps to connect a fiber-optic cable to a XENPAK module:

Caution

Do not remove the rubber plugs from the XENPAK module ports or the rubber 
caps from the fiber-optic cable until you are ready to connect the cable. The plugs 
and caps protect the XENPAK module ports and cables from contamination and 
ambient light.

Note

The 10-Gigabit Ethernet XENPAK modules are referred to as 10-Gigabit Ethernet 
module ports in the switch software documentation.

Note

Make sure that the XENPAK module is fully inserted into the module slot and that 
the captive installation screws are fully tightened before attaching the fiber-optic 
interface cable connector to the XENPAK module connector.

Step 1

Remove the rubber plugs from the XENPAK module ports and fiber-optic cable, 
and store them for future use.

Step 2

Align the fiber-optic cable SC connector with the XENPAK module connector, so 
that transmit (TX) on the cable meets receive (RX) on the XENPAK module 
connector, and RX on the cable meets TX on the XENPAK module.

Step 3

Insert the fiber-optic cable connector into the XENPAK module ports (see 

Figure 3-48

).

Содержание 3750 - Catalyst EMI Switch







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды