Cisco 3750 - Catalyst EMI Switch Скачать руководство пользователя страница 43

Страница: 43 / 230

1-11

Catalyst 3750 Switch Hardware Installation Guide

78-15136-03

Chapter 1 Using Express Setup

Configuring the Switch

Follow these steps to configure your switch by using Express Setup:

Step 1

Contact your system administrator and obtain the management VLAN ID, the IP
address, the IP subnet mask, and the default gateway for your switch.

Step 2

Enter a VLAN ID in the

Management Interface

(VLAN ID)

field. This is the

management interface through which you manage the switch and to which you
assign IP information. The Management Interface field displays

by default. The

VLAN ID range for this field is 1 to 1001.

Note

The

Management Interface (VLAN ID)

field is only available on

switches running Cisco IOS Release 12.1(20)EA1 or 12.2(18)SE or later.

Step 3

Enter the IP address of the switch in the

IP Address

field.

Step 4

Click the drop-down arrow in the

IP Subnet Mask

field, and select an

IP Subnet

Mask

Step 5

Enter the IP address for the default gateway in the

Default Gateway

field.

A gateway (router or dedicated network device) is a system that connects a
network on one subnet to one or more networks on a different subnet.

You must specify a default gateway if the management workstation and the switch
are on different IP segments.

Step 6

Enter your password in the

Switch Password

field.

The password can be from 1 to 25 alphanumeric characters, can start with a
number, is case sensitive, allows embedded spaces, but does not allow embedded
spaces at the beginning or end.

Step 7

Enter your password again in the

Confirm Switch Password

field.

You do not enter a username for the switch. After the switch is configured with an
IP address, you can use CMS to configure a username.

Step 8

(Optional) Enter a host name for the switch in the

Host Name

field. The host

name is limited to 31 characters; embedded spaces are not allowed.

Step 9

(Optional) Enter the name of your system contact in the

System Contact

field.

This identifies the system administrator for the switch or network.

Содержание 3750 - Catalyst EMI Switch







































































































































































































































Результаты поиска

Содержание 3750 - Catalyst EMI Switch

Отзывы:

Бренды по названию

Популярные бренды

Cisco 3750 - Catalyst EMI Switch, Руководство по установке оборудования

Результаты поиска

Содержание 3750 - Catalyst EMI Switch

Отзывы:

Бренды по названию

Популярные бренды