manualshive.com logo in svg

Cisco 3750 - Catalyst EMI Switch, Руководство по установке оборудования

Поделиться
Скачать
Cisco 3750 - Catalyst EMI Switch Скачать руководство пользователя страница 131

 

3-53

Catalyst 3750 Switch Hardware Installation Guide

78-15136-03

Chapter 3      Switch Installation

Connecting to the 10/100 and 10/100/1000 Ports

Note

You can use the 

mdix auto 

interface configuration command in the CLI to enable 

the automatic medium-dependent interface crossover (Auto-MDIX) feature. 
When the Auto-MDIX feature is enabled, the switch detects the required cable 
type for copper Ethernet connections and configures the interfaces accordingly. 
Therefore, you can use either a crossover or a straight-through cable for 
connections to a copper 10/100, 10/100/1000, or 1000BASE-T SFP module port 
on the switch, regardless of the type of device on the other end of the connection.

The Auto-MDIX feature is enabled by default on switches running Cisco IOS 
Release 12.2(18)SE or later. For releases between Cisco IOS 
Release 12.1(14)EA1 and 12.2(18)SE, the Auto-MDIX feature is disabled by 
default. For configuration information for this feature, refer to the switch software 
configuration guide or the switch command reference

.

Follow these steps to connect to 10BASE-T, 100BASE-TX or 1000BASE-T 
devices:

Caution

PoE faults are caused when noncompliant cabling or powered devices are 
connected to a PoE port.  Only standard-compliant cabling can be used to connect 
Cisco pre-standard IP Phones and wireless access points or 
IEEE 802.3af-compliant devices to PoE ports.  A cable or device that causes a 
PoE fault must be removed from the network. 

Step 1

When connecting to workstations, servers, routers, and Cisco IP Phones, connect 
a straight-through cable to an RJ-45 connector on the front panel. (See 

Figure 3-45

.) When connecting to switches or repeaters, use a crossover cable. 

(See the 

“Cable and Adapter Specifications” section on page B-5

 for cable-pinout 

descriptions.)

Note

When connecting to 1000BASE-T-compatible devices, be sure to use a 
twisted four-pair, Category 5 cable.

Содержание 3750 - Catalyst EMI Switch







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды