Cisco 3750 - Catalyst EMI Switch Скачать руководство пользователя страница 116

Страница: 116 / 230

Chapter 3 Switch Installation

Connecting StackWise Cable to StackWise Ports

3-38

Catalyst 3750 Switch Hardware Installation Guide

78-15136-03

•

Run the setup program. See the

“Completing the Setup Program” section on

page C-11

•

Connect to the front-panel ports. See the

“Connecting to the 10/100 and

10/100/1000 Ports” section on page 3-51

, the

“Connecting to an SFP

Module” section on page 3-55

, and the

“Connecting to a XENPAK Module”

section on page 3-59

to complete the installation.

To use the CLI, enter commands at the

Switch

> prompt through the console port

by using a terminal program or through the network by using Telnet. For
configuration information, refer to the switch software configuration guide or the
switch command reference

Connecting StackWise Cable to StackWise Ports

Follow these steps to connect the StackWise cable to the StackWise ports:

Step 1

Remove the dust covers from the StackWise cables and StackWise ports, and store
them for future use.

Step 2

Insert one end of the StackWise cable into the StackWise port on the back of the
switch.

Note

Always use a Cisco-approved StackWise cable to connect the switches.

Step 3

Use the window in the StackWise cable to align the connector correctly. Secure
the screws tightly.

Step 4

Insert the other end of the cable into the connector of the other switch, and secure
the screws tightly.

Caution

Removing and installing the StackWise cable can shorten its useful life.
Do not remove and insert the cable more often than is absolutely
necessary.

Содержание 3750 - Catalyst EMI Switch







































































































































































































































Результаты поиска

Содержание 3750 - Catalyst EMI Switch

Отзывы:

Бренды по названию

Популярные бренды

Cisco 3750 - Catalyst EMI Switch, Руководство по установке оборудования

Результаты поиска

Содержание 3750 - Catalyst EMI Switch

Отзывы:

Бренды по названию

Популярные бренды