manualshive.com logo in svg

Cisco 3750 - Catalyst EMI Switch, Руководство по установке оборудования

Поделиться
Скачать
Cisco 3750 - Catalyst EMI Switch Скачать руководство пользователя страница 44

 

Chapter 1      Using Express Setup

Configuring the Switch

1-12

Catalyst 3750 Switch Hardware Installation Guide

78-15136-03

Step 10

(Optional) Enter your system location in the 

System Location

 field. This 

identifies the physical location of the switch. 

Step 11

(Optional) Click 

Enable

 in the 

Telnet Access

 field if you are going to use Telnet 

to manage the switch by using the CLI. If you enable Telnet access, you must enter 
a Telnet password:

a.

Enter a password in the 

Telnet Password

 field. The Telnet password can be 

from 1 to 25 alphanumeric characters, is case sensitive, allows embedded 
spaces, but does not allow embedded spaces at the beginning or end.

b.

Enter the Telnet password again in the 

Confirm Telnet Password

 field.

Step 12

(Optional) Click 

Enable

 to configure Simple Network Management Protocol 

(SNMP). Enable SNMP only if you plan to manage switches by using Cisco 
Works or another SNMP-based network-management system.

If you enable SNMP, you must enter a community string in the 

SNMP Read 

Community

 field, the 

SNMP Write Community

 field, or both. SNMP 

community strings authenticate access to MIB objects. Embedded spaces are not 
allowed in SNMP community strings. If you set the SNMP read community, users 
can access MIB objects, but cannot modify them. If you set the SNMP write 
community, users can access and modify MIB objects.

Step 13

Click 

Save

 to save your settings to the switch, or click 

Cancel 

to clear your 

settings.

The switch exits Express Setup mode.

Your switch is now configured with the new IP address. You can install the switch 
in your production network.

Содержание 3750 - Catalyst EMI Switch







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды