manualshive.com logo in svg

Cisco 3750 - Catalyst EMI Switch, Руководство по установке оборудования

Поделиться
Скачать
Cisco 3750 - Catalyst EMI Switch Скачать руководство пользователя страница 64

 

Chapter 2      Product Overview

Front Panel Description

2-16

Catalyst 3750 Switch Hardware Installation Guide

78-15136-03

System LED

The System LED shows whether the system is receiving power and is functioning 
properly. 

Table 2-1

 lists the LED colors and their meanings.

For information on the System LED colors during power-on self-test (POST), see 
the 

“Powering On the Switch and Running POST” section on page 3-12

.

RPS LED

The RPS LED shows the RPS status. 

Table 2-2

 lists the LED colors and their 

meanings. 

Table 2-1

System LED

Color

System Status

Off

System is not powered on.

Green

System is operating normally.

Amber

System is receiving power but is not functioning properly.

Table 2-2

RPS LED

Color

RPS Status

Off

RPS is off or not properly connected.

Green

RPS is connected and ready to provide back-up power, if required.

Flashing green

RPS is connected but is unavailable because it is providing power to another device 
(redundancy has been allocated to a neighboring device).

Amber

The RPS is in standby mode or in a fault condition. Press the Standby/Active button 
on the RPS, and the LED should turn green. If it does not, the RPS fan could have 
failed. Contact Cisco Systems.

Flashing amber

The internal power supply in a switch has failed, and the RPS is providing power 
to the switch (redundancy has been allocated to this device).

Содержание 3750 - Catalyst EMI Switch







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды