manualshive.com logo in svg

Cisco 3750 - Catalyst EMI Switch, Руководство по установке оборудования

Поделиться
Скачать
Cisco 3750 - Catalyst EMI Switch Скачать руководство пользователя страница 57

 

2-9

Catalyst 3750 Switch Hardware Installation Guide

78-15136-03

Chapter 2      Product Overview

Front Panel Description

Note

100BASE-TX and 1000BASE-T traffic requires Category 5 cable. 10BASE-T 
traffic can use Category 3 or Category 4 cables.

When connecting the switch to workstations, servers, routers, and Cisco IP 
Phones, be sure that the cable is a straight-through cable. When connecting the 
switch to switches or hubs, use a crossover cable. When using a straight-through 
or crossover cable for 1000BASE-T connections, be sure to use a twisted 
four-pair, Category 5 cable for proper operation. Pinouts for the cables are 
described in 

Appendix B, “Connector and Cable Specifications.”

Note

You can use the 

mdix auto 

interface configuration command in the CLI to enable 

the automatic medium-dependent interface crossover (Auto-MDIX) feature. 
When the Auto-MDIX feature is enabled, the switch detects the required cable 
type for copper Ethernet connections and configures the interfaces accordingly. 
Therefore, you can use either a crossover or a straight-through cable for 
connections to a copper 10/100, 10/100/1000, or 1000BASE-T SFP module port 
on the switch, regardless of the type of device on the other end of the connection.

The Auto-MDIX feature is enabled by default on switches running Cisco IOS 
Release 12.2(18)SE or later. For releases between Cisco IOS 
Release 12.1(14)EA1 and 12.2(18)SE, the Auto-MDIX feature is disabled by 
default. For configuration information for this feature, refer to the switch software 
configuration guide or the switch command reference

.

Содержание 3750 - Catalyst EMI Switch







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды