Circutor SVGm-3WF-100C-480 Скачать руководство пользователя страница 52

Страница: 52 / 102

SVGm

Instruction Manual

Table 23 (Cont�): Warnings messages�

Alarm and event messages

Corrective

action

Replace the fans and reset the maintenance meter. (see “

10.- MAINTENANCE

”)

Fan deterioration

Description

Deterioration in the ventilation capacity of the system has been detected.

Corrective

action

Check that the fans are clean. Perform the periodic maintenance tasks. Replace the fans if this does

not solve the problem. (see “

10.- MAINTENANCE

”)

Mains voltage out of limits

Description

Mains voltage below the minimum

Corrective

action

This alert may be associated with transients and noise in the power supply voltage, or with incorrect

mains frequency values. Check the configuration. Check the quality of the power supply voltage. If it

continues, contact the

TAS�

Min temperature

Description

Temperature below the minimum operating value

Corrective

action

Wait for the environmental conditions to meet the requirements. If the alarm continues, contact the

TAS�

Mains frequency limits

Description

Main frequency out of the limits

Corrective

action

This alert may be associated with transients and noise in the power supply voltage, or with incorrect

mains frequency values. Check the configuration. Check the quality of the power supply voltage. If it

continues, contact the

TAS�

Minimum current

Description

Mains current below the programmed level.

Corrective

action

Check the configuration.

Maximum load

Description

Static generator working at full load

Corrective

action

No action is necessary.

Low power factor

Description

The power factor value measured is less than 0.7, which might indicate a connection error in the

measuring transformers, where the voltage phases do not correspond to the current phases.

Corrective

action

Confirm that the connections are correct.

Negative power

Description

The power value measured is negative (generated power), which might indicate that the transformers

have been connected inversely.

Corrective

action

Confirm that the connections are correct.

Wxxx

Description

Internal error.

Corrective

action

Contact the Technical Assistance Service.

Parallel SVGm in alarm

Description

This is a fault in one or more slaves.

Corrective

action

The device does not stop and adjusts its operation to the number of available slaves. On the slave

device status screen, “

6.12.- SLAVE DEVICE STATUS

” you can view the status and alarms for each

static generator. If there is a communications error with any of the slaves, stop the devices and check

the communications wiring.

Содержание SVGm-3WF-100C-480







































































































Результаты поиска

Содержание SVGm-3WF-100C-480

Отзывы:

Похожие инструкции для SVGm-3WF-100C-480

Бренды по названию

Популярные бренды

Circutor SVGm-3WF-100C-480, Инструкция по эксплуатации

Результаты поиска

Содержание SVGm-3WF-100C-480

Отзывы:

Похожие инструкции для SVGm-3WF-100C-480

Бренды по названию

Популярные бренды