Circutor SVGm-3WF-100C-480 Скачать руководство пользователя страница 60

Страница: 60 / 102

SVGm

Instruction Manual

7�5�- cos

Note:

This screen is not visible on the

“slave”

devices.

The device has two reactive power compensation modes (

Figure 63)�

Figure 63: Configuration screen: cos

(Mode 1 and Mode 2)�

●

Mode 1

In this mode, cos

is set to a fixed value. The device will attempt to ensure that the reactive power on

the mains side corresponds to the specified cos

Range of values:

0.7... -0.7

●

Mode 2

In this mode, two limits are defined to form an acceptance range. The device will adjust the reactive

power on the mains side to keep cos

within the specified acceptance range.

This mode minimises the amount of power used by the device to compensate for reactive power, thus

reducing its energy consumption.

Range of values:

0.7... -0.7

Press the

key to access the next configuration step

Press the

key to access the main screen of the device without saving the configuration values.

Содержание SVGm-3WF-100C-480







































































































Результаты поиска

Содержание SVGm-3WF-100C-480

Отзывы:

Похожие инструкции для SVGm-3WF-100C-480

Бренды по названию

Популярные бренды

Circutor SVGm-3WF-100C-480, Инструкция по эксплуатации

Результаты поиска

Содержание SVGm-3WF-100C-480

Отзывы:

Похожие инструкции для SVGm-3WF-100C-480

Бренды по названию

Популярные бренды