Circutor SVGm-3WF-100C-480 Скачать руководство пользователя страница 73

Страница: 73 / 102

Instruction Manual

SVGm

10.- MAINTENANCE

The

SVGm

static generator requires minimum preventive maintenance.

It is recommended to follow the notes described in this chapter to avoid premature

damage to the device's components.

Table 35

shows the maintenance jobs with their respective time intervals.

Table 35: Static generator maintenance�

Description

Interval

Standard maintenance

12 months

Replacement of the cooling fans

40000 h

SVGm-3WF-xxxC-690 and SVGm-4WF-xxxC-550:

Surge protective devices maintenance

12 months and after

adverse weather events

The device controls the maintenance intervals and shows the

symbol on the main screen of the

device if maintenance is required.

The warnings screen, “

6.8.- WARNINGS

” describes the type of maintenance procedures that must be

carried out.

Note:

The time intervals of the maintenance operations can vary depending on the device’s operating

conditions and environmental factors.

Follow the safety instructions in the

“SAFETY PRECAUTIONS”

section before carrying out

any maintenance on the

SVGm

Failure to follow these instructions may result in injury or even death�

Certain components in the device can reach high temperatures� Allow the device to

cool down before performing any maintenance operations�

10�1�- STANDARD MAINTENANCE

Perform maintenance every 6 to 12 months, depending on the level of environmental

dirt and operation of the device.

The device will indicate that the maintenance procedures must be carried out every 12

months.

For an installation with devices in parallel, standard maintenance must be performed on

all devices at the same time.

Содержание SVGm-3WF-100C-480







































































































Результаты поиска

Содержание SVGm-3WF-100C-480

Отзывы:

Похожие инструкции для SVGm-3WF-100C-480

Бренды по названию

Популярные бренды

Circutor SVGm-3WF-100C-480, Инструкция по эксплуатации

Результаты поиска

Содержание SVGm-3WF-100C-480

Отзывы:

Похожие инструкции для SVGm-3WF-100C-480

Бренды по названию

Популярные бренды