Ciena 170-3930-900 Скачать руководство пользователя страница 72

Страница: 72 / 104

5-4

LED Overview

3930 Service Delivery Switch

Hardware Installation and Start-up Manual

009-3223-001 Standard Revision E

2012-2014 Ciena

Corporation

January 2014

Power Supply LEDs

Each power supply module has integrated LEDs on the left section of the
faceplate. See

Figure 5-3

Figure 5-3
Power Supply LEDs

Table 5-3
Power Supply LEDs

LED

Indication

Description

INPUT

Off

Input power is not present. Or input power is outside of the
specified range. Or an internal failure has occurred.

Green

Input power is present and is within the specified range.

OUTPUT

Off

No input power present

Green

Output power is present and within acceptable limits. In
addition, the locally determined temperature is within the
normal operating range.

Red

One of the following conditions is present:

• Output power is not within the specified limits.

• System ordered power shutdown

• Locally determined over-temperature condition.

Содержание 170-3930-900


































































































Результаты поиска

Содержание 170-3930-900

Отзывы:

Бренды по названию

Популярные бренды

Ciena 170-3930-900, Руководство по установке и запуску оборудования

Результаты поиска

Содержание 170-3930-900

Отзывы:

Бренды по названию

Популярные бренды