manualshive.com logo in svg

Ciena 170-3930-900, Руководство по установке и запуску оборудования

Поделиться
Скачать
Ciena 170-3930-900 Скачать руководство пользователя страница 63

4-1

3930 Service Delivery Switch

Hardware Installation and Start-up Manual

009-3223-001   Standard    Revision E

Copyright

©

 2012-2014 Ciena

®

 Corporation

January 2014

Maintenance

4-

The 3930 is designed so that the cabling, optics, and power supply units are 
hot swappable. This means that the unit can remain powered for all these 
maintenance tasks. There is no requirement to remove power from the unit 
before performing these types of routine maintenance. 

Note:  

If you have opted to power both DC power supplies from the same 

circuit, you will need to power down the system to replace a power supply. 
Ciena recommends that each power supply be fed from a separate circuit 

This chapter provides maintenance instructions related to the power supply 
modules. It includes the following procedures:

•

“Replacing an AC Power Supply”

•

“Replacing a DC Power Supply”

Replacing a Power Supply Module

The 3930 has space for two power supply modules. The system can operate 
with a single power supply or with redundant power supplies. An overview of 
the power supply modules is included in 

39XX/51XX Product Fundamentals

.

Note:  

The system does not distinguish between a faulty and an 

unpowered supply. As a result, if redundant power supplies are installed, 
but only one supply is connected to a power source, the unpowered 
supply will cause the system to report an alarm state (ALRM LED solid 
yellow and STAT LED off). This alarm will be cleared when the power 
supply is properly initialized.

Simplex Power

If a single power supply is used, replacing the power supply will be a service 
impacting procedure.

Redundant Power 

If redundant power supplies are used, replacing a power supply does not need 
to be a service impacting procedure. 

Содержание 170-3930-900









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды