Ciena 170-3930-900 Скачать руководство пользователя страница 71

Страница: 71 / 104

LED Overview

5-3

3930 Service Delivery Switch

Hardware Installation and Start-up Manual

009-3223-001 Standard Revision E

2012-2014 Ciena

Corporation

January 2014

Table 5-1
Unit Status LEDs on 3930 Standard and 3930 Sync systems

LED

Indication

Description

STAT

Off

System is not powered or is not operating normally.

Green

Indicates status normal/system ready.

Blinking Green

System is initializing and performing self tests.

PWR

Green

Turns on when power is applied and remains on until the
system is powered off.

ALRM

Off

Normal operating conditions.

Yellow

An error has been detected.

TEMP

Off

System temperature is within the defined operating range.

Yellow

Over temperature alarm condition present. The system
temperature has exceeded the operating temperature
range.

Table 5-2
Unit Status LEDs on a 3930 Sync + External Timing system

LED

Indication

Description

STAT

Off

System is not powered or is not operating normally.

Green

Indicates status normal/system ready.

Blinking Green

System is initializing and performing self tests.

ALRM

Off

Normal operating conditions.

Yellow

An error has been detected.

SYNC

Off

System is in free run timing mode.

Green

System is locked to a synchronization source (external
input such as 1588, SyncE, etc).

Blinking Green

System is acquiring synchronization.

Yellow

System is in holdover timing mode.

Содержание 170-3930-900


































































































Результаты поиска

Содержание 170-3930-900

Отзывы:

Бренды по названию

Популярные бренды

Ciena 170-3930-900, Руководство по установке и запуску оборудования

Результаты поиска

Содержание 170-3930-900

Отзывы:

Бренды по названию

Популярные бренды