Ciena 170-3930-900 Скачать руководство пользователя страница 38

Страница: 38 / 104

2-22

Installation

3930 Service Delivery Switch

Hardware Installation and Start-up Manual

009-3223-001 Standard Revision E

2012-2014 Ciena

Corporation

January 2014

Note:

After it is installed, the power cord will be dressed to the right, across

the front of the power supply. It is not appropriate to dress the power cord to
the left, across the front of the 3930 chassis.

Remove power from the DC circuit(s) that will supply power to the system.

Using a flat head screwdriver, remove the plastic terminal block cover from
the front of both power supplies and set them aside.

Use the terminal block on the front of the DC power supply to connect the
wires as follows:

•

Ground — connect to the right connector

•

Negative — connect to the middle connector

•

Positive — connect to the left connector

Note:

The ground connection should be made first. The wires should be

installed so they flow down from the terminal block. The power cabling will be
dressed to the right in

step 11

Figure 2-4

shows the faceplate of the DC power supply with the power wiring

installed, and the plastic terminal block cover removed.

Figure 2-4
DC Power Supply (with cover removed and wiring installed)

Tighten the set screws on the terminal block with a Phillips screwdriver.

Repeat

step 7

and

step 8

to connect wires to the terminal block on the front

of the second power supply.

WARNING:

When making connections to the terminal block, make sure that no stray

strands of the input wire come into contact with any other part of the terminal block.

Содержание 170-3930-900


































































































Результаты поиска

Содержание 170-3930-900

Отзывы:

Бренды по названию

Популярные бренды

Ciena 170-3930-900, Руководство по установке и запуску оборудования

Результаты поиска

Содержание 170-3930-900

Отзывы:

Бренды по названию

Популярные бренды