manualshive.com logo in svg

Chore-Time Chore-Tronics 3 Control, Инструкция по установке и эксплуатации, Страница: 12 / 142

Поделиться
Скачать
Chore-Time Chore-Tronics 3 Control Скачать руководство пользователя страница 12

Glossary of Terms

Glossary of Terms

Chore-Tronics® 3 Control

12

MT2398C

Analog Input

Analog Inputs can consist of the following:

Temperature sensors

Static Pressure sensor (4-20 mA)

Relative Humidity Sensor (0-10 volts)

Potentiometer (Natural Ventilation)

Anticipation

When the control is turning on the fans assigned to the Minimum Ventilation Timer, the control will open 
the inlets to the correct position for static pressure control before the fans are turned on. If calculated 
anticipation is used (default), the control teaches itself how much adjustment was required during the 
previous on-off cycle, and uses that amount of "anticipation" for the next cycle. If the optional fixed 
anticipation is used, the control will NOT teach itself what the correct anticipation should be. It uses the 
amount of "anticipation" that is entered in the Static Pressure screen (Screen 11). Anticipation will occur 
when the fans assigned to the Minimum Ventilation Timer turn on due to the timer reaches an ON cycle 
or the sensor(s) assigned to the fans reach the fans' ON temperature.

Back Up Relay Output

The backup up relay output is a relay that will be energized as soon as the backup output is assigned to a 
relay. This relay will stay energized as long as the control is communicating with the manual switch board 
where the output is assigned. The 24 Vdc signal that comes from the control to the back up box should be 
routed through this relay. If communication is lost between the main box and the manual switch board, 
the relay will drop out allowing the first fan stage in the back up box to turn on. See the Wiring Diagrams 
section of this manual for more wiring information.

Bend Point (BP)

The Bend Points (BPs) are simply the points on the curve that define the curve. For the Set Temperature 
and Minimum Ventilation Timer curves, the curve values are gradually changed between bend points. The 
bend point values are the exact values at midnight beginning the day # of each bend point. The curve takes 
over when you turn the curve "on" and the day number is equal to or greater than the day number assigned 
to BP #1.

Cool Pad Output

The COOL PAD Output is a special function for controlling evaporative cooling that allows you to 
modulate the addition of water to the cooling pad in such a way that the usual large temperature swings 
associated with a cooling pad are avoided.

Curve

A "curve" is a listing of up to 10 points in time (bend points) that defines how you
want a parameter to automatically vary as the animals age.

Curve Value

The Control will list what the current value(s) the curve would be, if the current day
number is greater than the day # of bend point #1, and the curve is "on", and there is
no "offset" to the curve.

Day Number

The intention is that the day # is the age of the animals whose environment is being
controlled. Day # 0 does not exist. Negative days (down to - 7) are allowed.
Changing the day # in any screen that shows the day number, will change the day #
in all the other screens that show the day #.

Содержание Chore-Tronics 3 Control















































































































































Отзывы:

Нет отзывов