background image

6

Vectra Genisys®/Intelect Legend XT®/ Intelect® Vet Therapy Systems

2.2 PRECAUTIONARY INSTRUCTIONS (CONTINUED)

Use of controls or adjustments or performance of 
procedures other than those specified herein may result in 
hazardous exposure to ultrasonic energy.
Before administering any treatment to a patient you should 
become acquainted with the operating procedures for 
each mode of treatment available, as well as the indications, 
contraindications, warnings and precautions. Consult 
other resources for additional information regarding the 
application of Electrotherapy and Ultrasound.
To prevent electrical shock, disconnect the unit from 
the power source before attempting any maintenance 
procedures.
Keep electrodes separated during treatment. Electrodes in 
contact with each other could result in improper stimulation 
or skin burns.
Long term effects of chronic electrical stimulation are 
unknown.
Stimulation should not be applied over the anterior neck 
or mouth. Severe spasm of the laryngeal and pharyngeal 
muscles may occur and the contractions may be strong 
enough to close the airway or cause difficulty in breathing.
Stimulation should not be applied transthoracically in that 
the introduction of electrical current into the heart may 
cause cardiac arrhythmia.
Stimulation should not be applied over swollen, infected, 
and inflamed areas or skin eruptions, e.g., phlebitis, 
thrombophlebitis, varicose veins, etc.
Stimulation should not be applied over, or in proximity to, 
cancerous lesions.
Output current density is related to electrode size. Improper 
application may result in patient injury. If any question 
arises as to the proper electrode size, consult a licensed 
practitioner prior to therapy session.
The Vectra Genisys Therapy System optional modules and 
associated accessories are designed for use only with the 
Chattanooga Group Vectra Genisys Electrotherapy and 
Combination Therapy Systems.
Remove the Ultrasound or Laser Applicator by pulling the 
cable connector only. DO NOT remove by pulling the cable.

DO NOT connect the unit to an electrical supply without 
first verifying that the power supply is the correct 
voltage. Incorrect voltage may cause unit damage, 
malfunction, electrical shock, fire, or personal injury. Your 
unit was constructed to operate only on the electrical 
voltage specified on the Voltage Rating and Serial 
Number Plate. Contact your dealer if the unit is not 
properly rated.
When the unit is on, not all wavelengths are visible 
to the naked eye. Therefore, when performing any 
operational or functional check, make certain all persons 
in the vicinity of the laser wear Chattanooga Group laser 
protective eyewear.
DO NOT point the laser beam directly into human or 
animal eyes. The lens of the eye does not detect the 
invisible, coherent laser beams, potentially resulting in 
permanent retinal damage.
Class 3B Lasers are considered an acute hazard to the 
skin and eyes from direct radiation. Eye injury will occur 
is laser is viewed directly or from specular frelection. Eye 
protection is required for all persons in the treatment 
area.

Power Supplies retain High Voltage!

NiMH batteries contain Class E corrosive materials. In the 
event of battery cell rupture or leakage, handle battery 
module wearing neoprene or natural rubber gloves. 
Contents of a ruptured or leaking battery can cause 
respiratory irritation. Hypersensitivity to nickel can cause 
allergic pulmonary asthma. Contents of cell coming in 
contact with skin can cause skin irritation and chemical 
burns.
Never, under any circumstances, open the battery 
cells. Should an individual cell from a battery become 
disassembled, spontaneous combustion of the negative 
electrode is possible. There can be a delay between 
exposure to air and spontaneous combustion.

Charge the Battery Module according to the 
instructions found in this manual. Never attempt to 
charge the Battery Module on any other charging 
mechanism.

Use the Battery Module only with the Vectra Genisys 
Therapy Systems.
Do not reverse the polarity of the Battery Module. Doing 
so can increase the individual cell temperature and 
cause cell rupture or leakage.
Never dispose of Battery Module in fire. Never short 
circuit the battery. The battery may explode, ignite, leak 
or get hot causing serious personal injury.
Dispose of NiMH batteries according to national, state 
and local codes and regulations.

Stimulus delivered by the TENS waveforms of this 
device, in certain configurations, will deliver a charge of 
25 microcoulombs (μC) or greater per pulse and may 
be sufficient to cause electrocution. Electrical current 
of this magnitude must not flow through the thorax 
because it may cause a cardiac arrhythmia.
Patients with an implanted neurostimulation device 
must not be treated with or be in close proximity to 
any shortwave diathermy, microwave diathermy, 
therapeutic ultrasound diathermy or laser diathermy 
anywhere on their body. Energy from diathermy 
(shortwave, microwave, ultrasound and laser) can be 
transferred through the implanted neurostimulation 
system, can cause tissue damage, and can result in 
severe injury or death. Injury, damage or death can 
occur during diathermy therapy even if the implanted 
neurostimulation system is turned “off.”

Handle, clean and dispose of components and 
accessories that have come in contact with bodily 
fluids according to National, Local and Facility rules, 
regulations and procedures.

2 SAFETY PRECAUTIONS

Содержание Intelect Legend XT



















































































































Отзывы: