manualshive.com logo in svg

Chattanooga Group Intelect Legend XT, Руководство по обслуживанию

Поделиться
Скачать
Chattanooga Group Intelect Legend XT Скачать руководство пользователя страница 75

70

Vectra Genisys®/Intelect Legend XT®/ Intelect® Vet Therapy Systems

6 REMOVAL/REPLACEMENT

6.6 THERAPY SYSTEM KEYMAT ASSEMBLY

A. Tools and Equipment Required

#1 Phillips Screwdriver
Needle Nose Pliers

B. Keymat Assembly Removal

Separate Top from Bottom. 

Refer to 6.3, 

part B.

Remove Fan. 

Refer to 6.4, part B.

Remove Control Board Assembly. 

Refer to 

6.5, part B

.

Remove eight Keymat PC Board Retaining 
Screws. 

See Figure 6.28

.

Starting at the top of the Keymat PC Board, 
lift board with one hand, push in and release 
the plastic clips holding the Keymat PC Board 
in position. 

See Figure 6.29

.

Remove Keymats from the System Top. 

See 

Figure 6.30.

C. Replacing Keymat Assembly

Replace with new Keymat Assembly Kit by 
reversing the 

steps 1- 6

 

above.

NOTE:

Do not over tighten the screws. Over 
tightening will damage the threads of the 
brass inserts.
Re-assemble Therapy System referring to 
the appropriate sections of this manual for 
proper instructions.

1.
2.

1.

2.
3.

4.

5.

6.

1.

2.

FIGURE 6.28

FIGURE 6.29

REMOVE 

RETAINING 

SCREWS

LIFT PC BOARD AND 

RELEASE PLASTIC CLIPS

FIGURE 6.30

REMOVE ALL THREE 

KEYMATS

DISCONNECT THE SYSTEM FROM THE POWER 
SOURCE (OUTLET OR REMOVE BATTERY MODULE IF 
INSTALLED) BEFORE ATTEMPTING ANY MAINTENANCE, 
INSTALLATION, REMOVAL, OR REPLACEMENT 
PROCEDURES TO PREVENT ELECTRICAL SHOCK AND 
POSSIBLE DAMAGE TO SYSTEM.

MAKE CERTAIN WHEN INSTALLING CONTROL BOARD 
ASSEMBLY TO KEYMAT PC BOARD PINS FROM THE 
CONTROL BOARD ALIGN WITH THE CONNECTOR ON 
THE KEYMAT PC BOARD.

Содержание Intelect Legend XT



















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды