manualshive.com logo in svg

Chattanooga Group Intelect Legend XT, Руководство по обслуживанию

Поделиться
Скачать
Chattanooga Group Intelect Legend XT Скачать руководство пользователя страница 56

51

Vectra Genisys®/Intelect Legend XT®/ Intelect® Vet Therapy Systems

5 TROUBLESHOOTING

5.17 ULTRASOUND DUTY CYCLE TEST

This test is performed using only the 5 cm

2

 Vectra 

Genisys, Intelect Legend XT or Intelect Vet Applicator.

A. Ultrasound Duty Cycle Test Procedures

Set up Ohmic Instruments UPM DT 
10 or DT 100 Ultrasound Power Meter 
per Operator’s Instructions and fill test 
reservoir with Degassed Water.
Place an Applicator into the Power Meter 
retainer. Make certain the Sound Head is 
completely submerged in the degassed 
water and centered directly over the 
Stainless Steel Cone. 

See Figure 5.23.

“Zero” meter.
Press Ultrasound Button. Press Edit Button.
Press Duty Cycle Button until 100% is 
displayed within the Duty Cycle icon.
Press Display Button until “Watts” appears 
within the Display icon.
Press “Start”.
Rotate Therapy Intensity Control clockwise 
until “Watts” is displayed. 

See Figure 5.24.

 

Compare Power Meter readings to 

Figure 

5.24

 to all settings for the respective 

Applicator being tested as shown in 

Figure 5.24.

Press Frequency Button until 3.3 MHz 
is displayed within the Frequency icon. 
Repeat test and compare readings to 

Figure 5.24.

B. Ultrasound Duty Cycle Test Results

  Duty Cycles fall within the specified  
  ranges as listed in 

Figure 5.24.

  Unit passed test.
  Readings fall outside specified ranges of  
 

Figure 5.24.

 

a)

  Possible bad degassed water in Power 

     Meter.
 

b)

 Possible use of Power Meter other than 

      Ohmic Instruments UPM DT 10 or 
      DT 100 Ultrasound Power Meter.
 

c)

  Possible bad or out of calibration 

      Applicator. Re-test with known good 
     Ultrasound Applicator.
 

d)

  Possible bad internal connection at 

     Ultrasound Board.
 

e)

  Check Ultrasound Board internal  

     connections.
 

f)

  Replace Ultrasound Board.

 

g)

 Replace Control Board.

1.

2.

3.
4.
5.

6.

7.
8.

9.

10.

1.

2.

FIGURE 5.23

FIGURE 5.24

USE ONLY DEGASSED WATER IN POWER METER FOR 

TESTING ULTRASOUND APPLICATORS. USE OF OTHER 

TYPES OF WATER WILL CAUSE FALSE TEST RESULTS. 

SEE 

PAGE 37

 FOR DEGASSED WATER RECIPES.

DO NOT AERATE WATER WHEN FILLING POWER METER

APPLICATOR OUTPUT SPECIFICATIONS

APPLICATOR SIZE

DUTY CYCLE

OUTPUT RANGE

5 cm

2

10%

0.8 - 1.2

20%

1.6 - 2.4

50%

4.0 - 6.0

100% (Continuous)

8.0 - 12.0

Содержание Intelect Legend XT



















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды