Chattanooga Group Intelect Legend XT Скачать руководство пользователя страница 37

Страница: 37 / 114

Vectra Genisys®/Intelect Legend XT®/ Intelect® Vet Therapy Systems

5 TROUBLESHOOTING

Code

Number

Type

Message

Probable Cause

Possible Remedies

135

Warning

Control Board Software upgrade warning.

Upgrade Control Board Software to latest version. Contact dealer or Chattanooga Group for latest
software upgrade and instructions.

136

Warning

Stim Board Main Software upgrade warning.

Upgrade Stim Board Software to latest version. Contact dealer or Chattanooga Group for latest
software upgrade and instructions.

137

Warning

Stim Board Main Software upgrade warning.

Upgrade Stim Board Software to latest version. Contact dealer or Chattanooga Group for latest
software upgrade and instructions.

138

Warning

Ultrasound Board Software upgrade warning.

Upgrade Ultrasound Board Software to latest version. Contact dealer or Chattanooga Group for
latest software upgrade and instructions.

139

Warning

Laser Board Software upgrade warning.

Upgrade Laser Board Software to latest version. Contact dealer or Chattanooga Group for latest
software upgrade and instructions.

140

Warning

MMC Software upgrade warning.

Upgrade MMC Software to latest version. Contact dealer or Chattanooga Group for latest software
upgrade and instructions.

141

Warning

Battery Module Software upgrade warning.

Upgrade Battery Software to latest version. Contact dealer or Chattanooga Group for latest
software upgrade and instructions.

142

Warning

A Laser Protocol was selected but no Laser Module is
installed on system.

Install Laser Module to Therapy System. Refer to Laser Module User Manual for installation
Instructions.

143

Warning

A Laser Protocol was selected but no Laser Applicator
connected to system.

Connect proper Laser Applicator to the system.

If Laser Applicator is connected, reset Therapy System by turning main power switch

Off and On.

Connect a known good Laser Applicator.

If problem continues, send Laser Module to factory for Service.

144

Warning

Wrong Laser Applicator connected to system for the
protocol selected.

Connect correct Laser Applicator to the system.

If Applicator is connected, reset Therapy System by turning main power switch Off and On.

Connect a known good Laser Applicator.

If problem continues, send Laser Module to factory for Service.

145

Warning

Patient Data Card button on Home Screen was pressed
with no Patient Data Card installed into system port and
no treatment currently being performed.

Properly insert a Patient Data Card, set up and perform the treatment and, save data to Patient
Data Card.

5.1 THERAPY SYSTEM ERROR MESSAGES (CONTINUED)

Содержание Intelect Legend XT



















































































































Результаты поиска

Содержание Intelect Legend XT

Отзывы:

Бренды по названию

Популярные бренды

Chattanooga Group Intelect Legend XT, Руководство по обслуживанию

Результаты поиска

Содержание Intelect Legend XT

Отзывы:

Бренды по названию

Популярные бренды