Chamberlain CSW24U Скачать руководство пользователя | Manualshive

Страница: 33 / 60

background image

31

_

+

_

+

ACCESSORY WIRING

MISCELLANEOUS WIRING

THREE BUTTON CONTROL STATION

(4 Terminals)

•

OPEN and COM:

Opens a closed gate.

Hard open (maintained switch overrides external safeties and resets
alarm condition). If maintained, pauses Timer-to-Close at OPEN limit.
Opens a closing gate and holds open an open gate (within
line-of-sight).

•

CLOSE and COM:

Closes an open gate.

Hard close (maintained switch overrides external safeties and resets
alarm condition within line-of-sight)

•

STOP and COM:

Stops a moving gate.

Hard stop (maintained switch overrides Open and Close commands
and resets alarm condition). If maintained, pauses Timer-to-Close at
OPEN limit. Overrides Open and Close commands (within
line-of-sight).

FIRE DEPARTMENT OPEN INPUT

(2 Terminals)

Acts as hard open.

Maintained input overrides (ignores) external safeties (photoelectric
sensor and edge), pauses Timer-to-Close momentary input logic as single
button control and safeties remain active, re-enables Timer-to-Close.

ACCESSORY POWER 24 VDC, MAX 500 mA

(4 Terminals)

•

SWITCHED:

Switched ON with gate motion (stays on 5 seconds after

motion).

•

UNSWITCHED:

24 Vdc voltage out to power accessories, always ON.

Com

Open

(main control board)

Three Button Control Station

Fire Department

Com

Fire Dept

Acc Power +24 Vdc

Com (-)

(main control board)

Maglock

Solenoid Lock

(not provided)

(not provided)

(control board)

(control board)

Accessory Power Unswitched

Accessory Power Switched

Acc Power +24 Vdc

Com (-)

Close

Stop

N.C.

LOCKS

MAGLOCK

(2 Terminals, N.C. and COM)

Relay contact output, Normally - closed (N.C.) output for maglocks.

Relay activates prior to motor activation and during motor run. Relay is
off when motor is off.

SOLENOID

(2 Terminals, N.O. and COM)

Normally - open (N.O.) output for solenoid locks

Relay activates prior to motor activation and during motor run. Relay is
off when motor is off.

NOTE:

To conserve power for solar applications, the lock relay will only

activate for four seconds near the close limit.

«
...
31
32
33
34
35
...
»

Содержание CSW24U





























































Отзывы:

Нет отзывов

Похожие инструкции для CSW24U

Бренд: O&O Страницы: 24

Бренд: CAME Страницы: 2

Whisper Drive Security+ 257858

Бренд: Chamberlain Страницы: 80

Бренд: Genius Страницы: 32

Estate Swing E-S 1100 Series

Бренд: FAAC Страницы: 53

Бренд: Xtreme Garage Страницы: 28

Бренд: tau Страницы: 40

ARM 3000 Series

Бренд: tau Страницы: 44

Бренд: tau Страницы: 60

Бренд: Normstahl Страницы: 20

Бренд: Roger Technology Страницы: 12

Бренд: Gatex Страницы: 18

Бренд: Beninca Страницы: 16

Бренд: Nice Страницы: 88

Бренд: CAME Страницы: 24

DAN Automatik MF30

Бренд: tau Страницы: 20

Бренд: Black & Decker Страницы: 2

Бренд: Black & Decker Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды