Chamberlain CSW24U Скачать руководство пользователя

Страница: 13 / 60

STEP 2

CONCRETE PAD AND OPERATOR
ATTACHMENT

CHECK the national and local building codes before installation.

NOTE:

When lifting the operator use the handle to avoid damaging

the operator.

1. Install the electrical conduit.

2. Pour a concrete pad (reinforced concrete is recommended). The

concrete pad should be 6 inches above the ground and deeper than
the frost line. Ensure the pad is tall enough to avoid possible flooding.

3. Secure the operator to the concrete pad with appropriate fasteners.

NOTE:

An alternative to a concrete pad is to post mount the operator

(refer to accessories).

4 Concrete
Anchors
1/2" x 3 1/2"

Below the frost line.

Check all national

and local codes.

6" Above Ground

28"

24"

Post Mount

CONDUIT LOCATION

MOUNTING FOOTPRINT

5.5"

4.5"

6.5"

1.5"

10"

28"

20"

15"

24"

13.6"

12.2"

6.1"

2.49"

14"

14.82"

(cover mounting distance)

(Conduit)

(Pad)

INSTALLATION

Содержание CSW24U




























































Результаты поиска

Содержание CSW24U

Отзывы:

Похожие инструкции для CSW24U

Бренды по названию

Популярные бренды

Chamberlain CSW24U, Руководство по установке

Результаты поиска

Содержание CSW24U

Отзывы:

Похожие инструкции для CSW24U

Бренды по названию

Популярные бренды