Chamberlain CSW24U Скачать руководство пользователя

Страница: 46 / 60

APPENDIX

TOP VIEW OF OPERATOR AND GATE

Gate Open

90°

Gate Hinge Center

26-1/2"

Output Shaft Center

Wall

28"

24"

Handle

STEP 2

CONCRETE PAD AND OPERATOR
ATTACHMENT

COMPACT INSTALLATION ONLY

Check the national and local building codes before installation.

1. Install the electrical conduit.

2. Pour a concrete pad (reinforced concrete is recommended). The

concrete pad should be 6 inches above the ground and deeper than
the frost line. Ensure the pad is tall enough to avoid possible flooding.

3. Secure the operator to the concrete pad with appropriate fasteners.

NOTE:

An alternative to a concrete pad is to post mount the operator

(refer to accessories).

4 Concrete
Anchors
1/2" x 3 1/2"

Below the frost

line. Check all

national and

local codes.

6" Above Ground

28"

Post Mount

24"

CONDUIT LOCATION

MOUNTING FOOTPRINT

5.5"

4.5"

6.5"

1.5"

10"

28"

20"

15"

24"

13.6"

12.2"

6.1"

2.49"

14"

14.82"

(cover mounting distance)

(Conduit)

(Pad)

24"-32"

STEP 1

DETERMINE LOCATION FOR CONCRETE
PAD AND OPERATOR

COMPACT INSTALLATION ONLY

DO NOT run the operator until instructed.

Refer to the illustration to determine the measurements and location of
the concrete pad.

NOTE:

When lifting the operator use the handle to avoid damaging the

operator.

NOTE:

There should only be a maximum of 4" (10.2 cm)

from the center of the hinge to the edge of the post or
column. If the distance is greater than 4" (10.2 cm)
entrapment protection for this area is required.

4" (10.2 cm) maximum

Содержание CSW24U




























































Результаты поиска

Содержание CSW24U

Отзывы:

Похожие инструкции для CSW24U

Бренды по названию

Популярные бренды

Chamberlain CSW24U, Руководство по установке

Результаты поиска

Содержание CSW24U

Отзывы:

Похожие инструкции для CSW24U

Бренды по названию

Популярные бренды