Chamberlain CSW24U Скачать руководство пользователя | Manualshive

Страница: 20 / 60

background image

18

Jumper

Black Wire

Red Wire

1. Turn OFF AC power to the operator.

2. Unplug the J15 plug labeled BATT on the control board by squeezing

the plug and pulling it from the control board. This disconnects the
ac/dc power to the control board.

3. Connect a jumper between the positive (+) terminal of one battery to

the negative terminal (-) of the other battery.

4. Connect the red wire from the J15 plug to the positive (+) terminal of

the battery.

5. Connect the black wire from the J15 plug to the negative (-) terminal

of the battery.

6. Plug the J15 plug back into the control board. This will power up the

control board.

NOTE:

You may see a small spark when plugging the

J15 plug into the board.

7. Turn ON AC power to the operator.

8. Turn ON the AC power switch on the operator.

STEP 8 continued...

AC POWER SWITCH

The AC Power switch on the operator will turn the incoming 120/240 Vac power ON or OFF. The operator's AC Power switch ONLY turns off AC power
to the control board and DOES NOT turn off battery power.

AC Power Switch

INSTALLATION

STEP 9

CONNECT BATTERIES

7AH BATTERIES

The batteries are charged in the circuit by the integrated transformer. The batteries are for battery backup.

J15 Plug

«
...
18
19
20
21
22
...
»

Содержание CSW24U





























































Отзывы:

Нет отзывов

Похожие инструкции для CSW24U

Бренд: iOpener Страницы: 2

Бренд: Mhouse Страницы: 36

Бренд: AlluGuard Страницы: 28

Бренд: PPA Страницы: 2

Бренд: Motorline professional Страницы: 14

Бренд: Wisniowski Страницы: 22

Бренд: Wisniowski Страницы: 48

Бренд: CAME Страницы: 96

Бренд: CAME Страницы: 112

Бренд: fadini Страницы: 36

Бренд: Jaytech Страницы: 13

Бренд: DTM System Страницы: 12

Бренд: Chamberlain Страницы: 40

Бренд: Roger Technology Страницы: 16

Бренд: Roger Technology Страницы: 12

Бренд: Dea Страницы: 19

Бренд: Dea Страницы: 20

Бренд: Dea Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды